Related Questions
What is the correct answer?
4
This practice considers an individual part's dimensions and tolerances and that part's relation to its related parts:
B. Geometric dimensioning and tolerancing
C. Creating datum references
D. Angular dimensioning tolerances
What is the correct answer?
4
The section view drawing in which one fourth of an object has been marked for removal is known as a ________ section.
What is the correct answer?
4
Approximately this much of the cost of product development and manufacture is determined at the design stage:
What is the correct answer?
4
This line pattern is composed of three dashes, one long dash on each end with a short dash in the middle:
What is the correct answer?
4
In the mechanical design process the first step is to ________.
B. Prepare rough sketches
What is the correct answer?
4
Objects that are symmetric can be shown effectively using this type of section:
What is the correct answer?
4
The 3-D commands on the Modeling toolbar include ________.
What is the correct answer?
4
This is a thin solid line directing attention to a note or dimension and starting with an arrowhead or dot:
What is the correct answer?
4
In offset sections, offsets or bends in the cutting plane are all:
C. Either 90 or 180 degrees
What is the correct answer?
4
Dimensions are used on the elevation plan to describe ________.
A. Finished floor elevations
What is the correct answer?
4
This is used in applications for nonferrous construction:
What is the correct answer?
4
This should show what changes were made, when, and by whom:
What is the correct answer?
4
When creating your own blocks it is important to avoid drawing any portion of the block in the ________ layer.
What is the correct answer?
4
A circular arc is dimensioned in the view where you see its true shape by giving the value for its:
What is the correct answer?
4
A fillet is a rounded surface on the ________ corner of a part.
What is the correct answer?
4
This is a rounded exterior blend between surfaces:
What is the correct answer?
4
Architectural drafters generally prefer to use ________ drawings to help illustrate 3-dimensional views of a structure.
What is the correct answer?
4
Technical drawings typically serve one of three purposes:
A. Visualization, Communication, or Documentation
B. Visualization, Dimensioning, or Documentation
C. Communication, Documentation, or Installation
D. Documentation, Installation, or Engineering
What is the correct answer?
4
The ________ tool on the Dimension tool bar places the length of an arch on a drawing.
What is the correct answer?
4
A back or backing weld is a type of:
What is the correct answer?
4
Two-point perspective is also known as:
What is the correct answer?
4
Before starting an isometric drawing in Auto-CAD the drafter needs to ________.
A. Set the grid to isometric
B. Set the current layer to Defpoints
What is the correct answer?
4
Architectural dimensioning standards allow for the placement of dimensions inside the floor plan. These inside dimensions locate interior __________.
A. Door openings and walls
What is the correct answer?
4
A ________ is the person responsible for verifying that the drawings in a project set are free of mistakes.
What is the correct answer?
4
This type of projection is when projectors are parallel to each other, but is at an angle other than 90 degrees to the plane of projection:
B. Perpendicular projection
What is the correct answer?
4
EDM is the acronym for:
A. Enterprise data management
B. Engineering drawing management
C. Enterprise drawing manipulation
D. Engineering data manipulation
What is the correct answer?
4
5.These items typically are not used in new designs, but are still common in high-power amplifiers:
What is the correct answer?
4
This process recognizes the inherent interrelationships between design and manufacturing:
A. Design for manufacture
B. Design for manufacture and assembly
C. Design for concurrent engineering
What is the correct answer?
4
3.When lines intersect on a drawing at angles of this many degrees, it is customary not to dimension the angle:
What is the correct answer?
4
This is a conical-shaped recess around a hole, often used to receive a tapered screw head: