Related Questions
What is the correct answer?
4
The text used on a typical detail sheet should be ________.
C. In an architectural text style
What is the correct answer?
4
In this type of concrete, the steel is pre-tensioned before the superimposed load is applied:
What is the correct answer?
4
Architectural dimensioning standards allow for the placement of dimensions inside the floor plan. These inside dimensions locate interior __________.
A. Door openings and walls
What is the correct answer?
4
When creating an isometric drawing in Auto-CAD the drafter can utilize the Dynamic Input and Polar Coordinate system to place both vertical and horizontal lines. A line created from one point 3 inches at 180 degrees would be a ________ line.
What is the correct answer?
4
These units are based on inch-foot and yard measurements:
A. International customary units
D. ISO international units
What is the correct answer?
4
This type of projection is when projectors are parallel to each other, but is at an angle other than 90 degrees to the plane of projection:
B. Perpendicular projection
What is the correct answer?
4
The ________ tool on the Dimension tool bar will place several dimensions at one time by using a selection box placed over several part features.
What is the correct answer?
4
Architectural dimensioning is usually done in ________.
What is the correct answer?
4
There should be a visible gap between the wall and the ________ line.
What is the correct answer?
4
A ________ section allows the drafter to create a Cutting Plane line which is not in a straight line across the part.
What is the correct answer?
4
When using the direct entry method to create a horizontal line exactly three inches long the drafter should ________ first.
A. Pull the line from away from the starting point very carefully
B. Insure that Ortho is on
C. Enter 3 for the length of the line
D. Read the coordinate position on the Dynamic Readout
What is the correct answer?
4
Once a drawing is determined to be complete, the title block is used to document the change from:
A. A draft to a finished drawing
B. A finished to a working drawing
C. An assembly to a finished drawing
D. A working drawing to a draft
What is the correct answer?
4
The condition of a part when it contains the least amount of material is referred to as ________.
What is the correct answer?
4
In this type of projection, each of the axes has different ratios of foreshortening:
What is the correct answer?
4
A line with a tapering width can be easily created by using the __________ tool.
What is the correct answer?
4
CAD programs which incorporate parametric modeling utilize a system in which the dimensions control the ________.
A. Size and shape of the model features
B. Perspective of the model
C. Shading used to render the model
What is the correct answer?
4
When adding dimensions to an auxiliary view it will be necessary to use the ________ tool.
What is the correct answer?
4
In order to convert fractional inches into decimal inches ________.
A. Look on a metric conversion chart
B. Divide the numerator (top number) by the denominator (bottom number)
C. Check the engineer's scale
What is the correct answer?
4
This type of section is not in direct projection from the view containing the cutting plane:
What is the correct answer?
4
The principle views associated with orthographic projection are ________.
What is the correct answer?
4
A back or backing weld is a type of:
What is the correct answer?
4
Traditional drafters need to be able to create several different line widths because ________.
A. Different line widths convey different information
B. The line width has to do with how dark it appear in the finished drawing
C. They seem to transmit better in a fax machine
D. It makes no difference
What is the correct answer?
4
On a floor plan the dashed line that appears approximately 24 outside the exterior wall represents the __________.
What is the correct answer?
4
Several of the tools used in traditional drafting include the following:
A. Parallel straight edge
What is the correct answer?
4
Some of the common terms used to describe technical drawing include:
What is the correct answer?
4
This type of surface is tipped to all principal planes of projection and does not appear true size in any standard view:
What is the correct answer?
4
When the drafter types the word BLOCK or selects the Make Block tool from the Draw tool bar the ________ will appear.
C. Block Definition Dialog
What is the correct answer?
4
In a CAD system, you can draw an ellipse by specifying these:
B. The midpoint and end points
C. The center and major and minor axes
What is the correct answer?
4
Referring to the fractional inches to decimal inches to millimetre conversion chart on page 55 what is the equivalent mm measurement of 3/16 inch.
What is the correct answer?
4
The distance a screw thread advances axially in one turn is the: