Related Questions
What is the correct answer?
4
This is the plane upon which the top view is projected:
What is the correct answer?
4
PDM is the acronym for:
A. Project drawing management
B. Product drawing manipulation
C. Product data management
D. Project data manipulation
What is the correct answer?
4
The offset distance for the width (front to back) distance of the auxiliary view is the same distance of the ________ in the top view.
What is the correct answer?
4
This is the bottom surface joining the sides of two adjacent threads:
What is the correct answer?
4
Using the Relative Polar Coordinate System to add a 3 inch line that is 45 degrees from the end point of the line created above the drafter would ________.
B. Type 3 back slash and enter
C. Type 3 forward slash and enter
D. Type 3 and try to use the Dynamic Input readout to find the end point
What is the correct answer?
4
In offset sections, offsets or bends in the cutting plane are all:
C. Either 90 or 180 degrees
What is the correct answer?
4
When using the direct entry method to create a horizontal line exactly three inches long the drafter should ________ first.
A. Pull the line from away from the starting point very carefully
B. Insure that Ortho is on
C. Enter 3 for the length of the line
D. Read the coordinate position on the Dynamic Readout
What is the correct answer?
4
When only a small section of an interior area needs to be revealed the drafter can use a ________ section.
What is the correct answer?
4
In these drawings it is necessary to show cut surfaces and distinguish between adjacent parts:
What is the correct answer?
4
This is a common method for connecting steel members of buildings and bridges:
What is the correct answer?
4
The architectural drafter usually begins a set of working drawings by creating the ________ plan first.
What is the correct answer?
4
When designing a home for a client, one of the most important predesign considerations that an architect needs to address is ________.
A. How much money the client is willing to spend
B. The site on which the house is to sit
C. The nearest grocery store
D. Whether or not there is a curb and gutter system
What is the correct answer?
4
When the drafter types the word BLOCK or selects the Make Block tool from the Draw tool bar the ________ will appear.
C. Block Definition Dialog
What is the correct answer?
4
Dimension text is generally placed above the ________ line.
What is the correct answer?
4
Isometric drawings are often used by ________ to help illustrate complex designs.
What is the correct answer?
4
The ________ is a standard element of a section view in a technical drawing.
C. Material hatch pattern
What is the correct answer?
4
This is the intersection of the ground plane with the picture plane:
What is the correct answer?
4
5.These items typically are not used in new designs, but are still common in high-power amplifiers:
What is the correct answer?
4
When dimensioning architectural drawings architects will utilize both ________ and ________ options.
A. Baseline and continuous
What is the correct answer?
4
These are joined together in the field to build a structure:
D. Assembled fabrications
What is the correct answer?
4
One critical issue drafters need to pay close attention to is the ________.
What is the correct answer?
4
These weld symbols have no arrow-side or other-side significance:
A. Projection or seam weld
C. Surface or groove weld
What is the correct answer?
4
These types of pipes are generally connected with bell and spigot joints or flanged joints:
What is the correct answer?
4
By using a ________ section of a cylindrical mechanical part the drafter should be able to show only one view of the part.
What is the correct answer?
4
This is the total amount that the feature on the actual part is allowed to vary from what is specified by the dimension:
What is the correct answer?
4
This is used in drawings to represent the edge of a solid object:
What is the correct answer?
4
A fillet is a rounded surface on the ________ corner of a part.
What is the correct answer?
4
This practice considers an individual part's dimensions and tolerances and that part's relation to its related parts:
B. Geometric dimensioning and tolerancing
C. Creating datum references
D. Angular dimensioning tolerances
What is the correct answer?
4
Generally, the units used on an architectural drawing are set to ________.
What is the correct answer?
4
This type of circuit is a semiconductor wafer or chip: