This is formed where three or more surfaces intersect:
Oblique
Line
Edge
Vertex
Correct Answer :
D. Vertex
Related Questions
Once a drawing is determined to be complete, the title block is used to document the change from:
A draft to a finished drawing
A finished to a working drawing
An assembly to a finished drawing
A working drawing to a draft
A partial auxiliary view is used to show only the ________ in the auxiliary view.
Projected inclined plane
The projected top view
The projected side view
None of the above
This type of solid has two bases that are parallel equal polygons:
Pyramid
Prism
Cone
Torus
This is a conical-shaped recess around a hole, often used to receive a tapered screw head:
Boss
Spotface
Counterbore
Countersink
Auto-CAD refers to isometric ellipses as ________.
Ellipses
Iso-ellipses
Iso-circles
Circles
Drafters should use a ________ in a section view of a mechanical part that includes the cylindrical view of a threaded hole.
Center line
Hatch line
Poly line
Dimension line
There should be a visible gap between the wall and the ________ line.
Dimension
Extension
Center
Leader
The ________ is a standard element of a section view in a technical drawing.
Cutting Plane line
Section lines
Material hatch pattern
All of the above
Circular shapes appear in this fashion when viewed at an angle other than 90 degrees:
Circular
Elliptical
Lengthened
Angular
This is the intersection of the ground plane with the picture plane:
Vanishing point
Ground line
Station point
Horizon
This means that a feature of a finished product contains the maximum amount of material permitted by the tolerance dimensions for that feature:
Maximum material condition
Machined material condition
Maximum machined indication
Machine mark indication
A fillet is a rounded surface on the ________ corner of a part.
Inside
Outside
Radial
Isoplane
The ________ dimension tool will place the length of an angled line.
Aligned
Angle
Linear
Radial
In U.S. structural and architectural drafting, all dimensions of this length are usually expressed in feet and inches:
One inch or over
One foot or over
One yard or over
One rod or over
Most architectural firms and mechanical design companies utilize different categories of blocks. These sets of blocks are usually housed in ________.
Block vaults
Block libraries
Block books
Block references
Some traditional board drafters preferred the drafting machine over the parallel straight edge because it could be used without the need for________.
Circle templates
Triangles
Technical pens
Lettering guides
The distance a screw thread advances axially in one turn is the:
Lead
Pitch
Turn
Crest
The primary unit of measurement for engineering drawings and design in the mechanical industries is the:
Millimeter
Centimeter
Meter
Kilometer
By using a ________ section of a cylindrical mechanical part the drafter should be able to show only one view of the part.
Half
Whole
Revolved
Broken out
This type of axonometric drawing has equal foreshortening along two axis directions and a different amount on the third axis:
Dimetric
Multiview
Isometric
Trimetric
In this type of projection, each of the axes has different ratios of foreshortening:
Isometric
Dimetric
Trimetric
Parallel
Which of the following is one of the basic types of welded joints:
T-joint
Rear joint
Angle joint
Groove joint
The View toolbar will position the view of the 3-D solid toward the ________.
Front
Left side
SE isometric
All of the above
These drawings are given to contractors to perform work or manufacture individual parts:
Assembly details
3D drawings
Working drawings
Skeleton assemblies
A half-moon protractor is divided into how many degrees?
360
180
270
310
This is the total amount that the feature on the actual part is allowed to vary from what is specified by the dimension:
Allowance
Tolerance
Specification
Difference
A ________ section allows the drafter to create a Cutting Plane line which is not in a straight line across the part.
Offset
Half
Whole
Broken out
The most common geometric form used in gears today is this:
Involute profile
Convolute profile
Base circle
Spur circle
A partial auxiliary view usually shows only features on the ________ of the inclined line and not any projection of other planes.
Hidden lines
Plane
Center lines
None of the above
The default position of the UCS icon is positioned at ________ on the AutoCAD grid.
0, 0, 0
10, 10, 10
20, 20, 20
None of the above