Related Questions
What is the correct answer?
4
When drawing a line using the relative coordinate system a line is created from ________.
B. The ending point of the last line
C. The beginning point of the last line
What is the correct answer?
4
One critical issue drafters need to pay close attention to is the ________.
What is the correct answer?
4
When the drafter types the word BLOCK or selects the Make Block tool from the Draw tool bar the ________ will appear.
C. Block Definition Dialog
What is the correct answer?
4
Referring to the fractional inches to decimal inches to millimetre conversion chart on page 55 what is the equivalent mm measurement of 3/16 inch.
What is the correct answer?
4
This is a conical-shaped recess around a hole, often used to receive a tapered screw head:
What is the correct answer?
4
Given a situation in which the drafter has crossed extension lines in a drawing what can be done to clean up the point of crossing?
A. Use the Modify tool to clean up the extension lines
B. Use the Tolerance tool to clean up the extension lines
C. Use the Break tool to clean up the extension lines
D. Use the stretch tool to clean up the extension lines
What is the correct answer?
4
The text height for room names should be set to ________for a drawing that will be plotted to a scale of ¼ = 1'-0.
What is the correct answer?
4
In offset sections, offsets or bends in the cutting plane are all:
C. Either 90 or 180 degrees
What is the correct answer?
4
In oblique sketches, the most commonly used angles for receding lines are:
What is the correct answer?
4
In architectural drawing ________ are often used to illustrate and detail structural components.
A. Foundation beam detail sections
What is the correct answer?
4
This type of solid has a polygon for a base and triangular lateral faces that intersect at a vertex:
What is the correct answer?
4
The 3-D commands on the Modeling toolbar include ________.
What is the correct answer?
4
In order to create an accurate assembly drawing the drafter should create the ________ drawings first.
What is the correct answer?
4
This is a rounded exterior blend between surfaces:
What is the correct answer?
4
In order to set drawing limits for a C size architectural drawing the drafter should set the limits to ________.
What is the correct answer?
4
The default position of the UCS icon is positioned at ________ on the AutoCAD grid.
What is the correct answer?
4
The Auto-CAD command used to combine two or more primitive shapes into a single complex 3-dimensional model is ________.
What is the correct answer?
4
The Free Orbit tool is found on the ________ toolbar.
What is the correct answer?
4
Drawings created with commercial software are typically saved as:
What is the correct answer?
4
Inserting blocks into a drawing file usually requires exacting placement. The drafter should insure that ________ is turned on.
What is the correct answer?
4
The ________ tool on the Dimension tool bar will place several dimensions at one time by using a selection box placed over several part features.
What is the correct answer?
4
The View toolbar will position the view of the 3-D solid toward the ________.
What is the correct answer?
4
When positioning this feature of perspective projection, the centerline of the cone of visual rays should be directed toward the approximate center of the object:
What is the correct answer?
4
This is the smallest diameter of a screw thread:
A. Internal thread diameter
D. External thread diameter
What is the correct answer?
4
This type of surface is tipped to all principal planes of projection and does not appear true size in any standard view:
What is the correct answer?
4
When lettering a CAD drawing, for clarity you should limit the number of fonts to:
What is the correct answer?
4
An engineer's scale would be used to measure lines on a drawing where the scale factor reads ________.
What is the correct answer?
4
These are accurately drawn maps of cities and towns showing property lines and other features that control property ownership:
What is the correct answer?
4
A line with a tapering width can be easily created by using the __________ tool.
What is the correct answer?
4
Architectural drawings used to construct a house are often plotted with a scale of ¼ = 1'-0. What scale is this?