Related Questions
What is the correct answer?
4
The 3-D commands on the Modeling toolbar include ________.
What is the correct answer?
4
By using a ________ section of a cylindrical mechanical part the drafter should be able to show only one view of the part.
What is the correct answer?
4
If a designer is developing a plan for a project in which the entire part is made out of ¾ thick plywood and he only wants to use one view, he should use the ________ view.
What is the correct answer?
4
Drafters should use a ________ in a section view of a mechanical part that includes the cylindrical view of a threaded hole.
What is the correct answer?
4
In oblique sketches, the most commonly used angles for receding lines are:
What is the correct answer?
4
A typical set of mechanical working drawings includes ________.
What is the correct answer?
4
Circular shapes appear in this fashion when viewed at an angle other than 90 degrees:
What is the correct answer?
4
Technical drawings typically serve one of three purposes:
A. Visualization, Communication, or Documentation
B. Visualization, Dimensioning, or Documentation
C. Communication, Documentation, or Installation
D. Documentation, Installation, or Engineering
What is the correct answer?
4
This is a conical-shaped recess around a hole, often used to receive a tapered screw head:
What is the correct answer?
4
A ________ section allows the drafter to create a Cutting Plane line which is not in a straight line across the part.
What is the correct answer?
4
Students can complete an associate's degree in drafting which normally takes about ________ years to complete.
What is the correct answer?
4
The standard number of threads per inch for various diameters is the:
What is the correct answer?
4
One way to evenly space dimensions on a drawing is to use the ________.
What is the correct answer?
4
The offset distance for the width (front to back) distance of the auxiliary view is the same distance of the ________ in the top view.
What is the correct answer?
4
In some circumstances an entire drawing can be inserted into a different drawing as a block. When this is used the base point will default to ________.
What is the correct answer?
4
An engineer's scale would be used to measure lines on a drawing where the scale factor reads ________.
What is the correct answer?
4
This type of projection is when projectors are parallel to each other, but is at an angle other than 90 degrees to the plane of projection:
B. Perpendicular projection
What is the correct answer?
4
The site plan illustrates ________.
B. Where the house sits on the property
D. Where the garage and driveway are located
What is the correct answer?
4
The dimension text size is determined by what the architect deems necessary in __________.
What is the correct answer?
4
This allows the performance of structures to be analyzed and tested efficiently, accurately, and quickly:
A. Computer-aided manufacturing
C. Computer-aided engineering
D. Computer-aided prototyping
What is the correct answer?
4
Drawings created with commercial software are typically saved as:
What is the correct answer?
4
Schematic and single-line diagrams should be arranged so that signal or transmission path from input to output proceeds in this fashion:
A. Right to left and top to bottom
B. Right to left and bottom to top
C. Left to right and top to bottom
D. Left to right and bottom to top
What is the correct answer?
4
Perspective drawings are classified according to their number of these features:
What is the correct answer?
4
This is used to indicate that a surface is to be machined:
What is the correct answer?
4
This is the intersection of the ground plane with the picture plane:
What is the correct answer?
4
Some common blocks used by architectural drafters include ________.
What is the correct answer?
4
This is the total amount that the feature on the actual part is allowed to vary from what is specified by the dimension:
What is the correct answer?
4
The first step in creating a traditional technical drawing is to ________.
A. Draw a series of guide lines
C. Align the paper so that it will be positioned square to the parallel bar
D. Sharpen the leads in the technical pens
What is the correct answer?
4
A fillet is a rounded surface on the ________ corner of a part.
What is the correct answer?
4
These drawings are given to contractors to perform work or manufacture individual parts: