Related Questions
What is the correct answer?
4
__________ test can be termed as the semidestructive test.
What is the correct answer?
4
One face of a furnace wall is at 1030°C and the other face is exposed to room temperature (30°C). If the thermal conductivity of furnace wall is 3 W. m- 1. k-1 and the wall thickness is 0.3 m, the maximum heat loss (in W/m) is
What is the correct answer?
4
Which of the following low melting alloy containing bismuth and lead is used for electric fuse?
What is the correct answer?
4
Neutrons are present in all atoms except that of
What is the correct answer?
4
The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength.
What is the correct answer?
4
Velocity of a gas in sound is not proportional to (where, T = Absolute temperature of the gas. P = Absolute pressure of the gas. y = Ratio of specific heats (Cp/Cv) ρ = specific weight of the gas)
What is the correct answer?
4
Factor of safety is the ratio of the __________ stress to the working stress.
What is the correct answer?
4
Hydro-cyclone is a
What is the correct answer?
4
Steam condenser tubes are made of admiralty brass, in which percentage of zinc & copper are __________ respectively.
What is the correct answer?
4
Absolute zero pressure can be attained at a temperature of
What is the correct answer?
4
The only suitable method for hardening the low carbon steel is case hardening. Which of the following is a case hardening process?
What is the correct answer?
4
The normal stress is the same in all directions at a point in a fluid, only when the fluid
A. Is at rest & has zero viscosity
C. Fluid layer has no motion relative to an adjacent layer of fluid
D. is incompressible & frictionless
What is the correct answer?
4
Steels with high carbon equivalent have poor Weldability, because in these steels during welding
A. Carbon and other alloying elements get oxidised from the weld pool
B. Excessive ferrite forms in the heat affected zone leading to poor toughness of the weld
C. Martensite forms in the heat affected zone leading to poor toughness/ductility of the weld
D. Segregation of carbon and other element occurs in the weld pool leading to poor properties of the weld
What is the correct answer?
4
Out of the following, which will fracture most readity, when hit with a hard hammer?
What is the correct answer?
4
__________ is a special constituent of chlorophyll without which photosynthesis is not possible.
What is the correct answer?
4
Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal
D. Thermal co-efficient of expansion
What is the correct answer?
4
Silicon in steel
A. Makes it usable in almost all magnetic circuits where alternating current is used
B. Increases its electrical resistivity and decreases the hysteresis loss
C. Is present upto 5% & 4% respectively when used in transformers & motor armatures
What is the correct answer?
4
Normalising of an object does not
A. Refine coarse grain structure obtained during hot working
C. Improve yield strength
D. Improve mechanical properties
What is the correct answer?
4
The diffusion co-efficient of Ni in Cu at 1000 K is 1.93 × 10-16 m2S-1 and it is 1.94 × 10-14 m2S- 1 at 1200 K. The activation energy (in k. J.mole-1) for the diffusion of Ni in Cu is
What is the correct answer?
4
__________ the exhaust gas is an indication of the incomplete combustion of fuel.
What is the correct answer?
4
Young's modulus of a material is the measure of its
What is the correct answer?
4
The ability of tool steel to resist softening at high temperatures is termed as __________ hardness.
What is the correct answer?
4
Which of the following is not a charge material for cupola?
What is the correct answer?
4
__________ of austenite decreases the hardenability in steel.
D. Dissolved elements (except cobalt)
What is the correct answer?
4
Addition of __________ to steel does not impart hardness.
What is the correct answer?
4
In an eutectic system, two elements are completely
A. Soluble in solid state
B. Insoluble in liquid state
C. Insoluble in both solid & liquid state
D. Soluble in liquid state
What is the correct answer?
4
__________ of hard alloy and tool steel is done to make it easily machinable.
What is the correct answer?
4
Specific __________ is a dimensionless quantity.
What is the correct answer?
4
An approximately __________ process exemplifies the flow of a gas through a very long pipe of uniform cross-section.
What is the correct answer?
4
Eutectic reaction for iron-carbon system occurs at a temperature of __________ °C.