Related Questions
What is the correct answer?
4
Dielectric
A. Is an electrical insulating material
B. Of low resistivity is preferred
C. Should have high thermal conductivity
D. Need not defy the corrosive action of chemicals
What is the correct answer?
4
The 'transition temperature' for ductile to brittle behaviour of steel increases with increase in the __________ content in steel.
What is the correct answer?
4
The cathode in an electrochemical cell always carries
D. Positive or negative charge depending upon the nature of the cell
What is the correct answer?
4
Brinell Hardness Number (BHN) for talc is approximately in the range of
What is the correct answer?
4
The rolling process cannot be used to produce
What is the correct answer?
4
The same volume of all gases is representative of their
C. Gas characteristic constants
What is the correct answer?
4
Stellite is a __________ material.
D. Non-ferrous cast alloy cutting tool
What is the correct answer?
4
An oxidation process is accompanied with decrease in the
What is the correct answer?
4
Volume of blast furnace slag is about __________ times the volume of hot metal (pig iron) of the same weight
What is the correct answer?
4
Which of the following relationships is correct for relating the three elastic constants of an isotropic elastic material (where, E = Young's modulus, G = Modulus of rigidity or shear modulus v = Poisson's ratio)?
What is the correct answer?
4
__________ is the most suitable lubricant for drawing mild steel wires?
What is the correct answer?
4
Nickel is a __________ material.
What is the correct answer?
4
A material being tested for endurance strength is subjected to the __________ load.
What is the correct answer?
4
The thickness of oxide film is y at time t. If are the temperature dependent constants, the parabolic law of oxidation is given by
What is the correct answer?
4
Lead pencil contains
What is the correct answer?
4
Calorific value of __________ are almost same.
A. Lignite & anthracite coal
D. Coal gas & natural gas
What is the correct answer?
4
Maximum permissible air velocity in pipelines is about __________ metre/second.
What is the correct answer?
4
The 'laughing gas' is
What is the correct answer?
4
A common disinfectant used in village wells for disinfection of water is
D. Potassium permanganate
What is the correct answer?
4
Venturimeter is used to measure the flow rate of fluids in pipes, when the pipe is in __________ position.
What is the correct answer?
4
Electrometallurgical methods of metal extraction is normally used for those metals
A. Whose oxide/ore is not reduced by carbon
B. Which fall in the category of alkali & alkaline earth metals
C. Which stands higher in the electrochemical series of the metal
What is the correct answer?
4
A material subjected __________ must have high resilience.
What is the correct answer?
4
Which of the following equipments is used for liquid dispersion?
C. Bubble cap plate column
What is the correct answer?
4
In inventory control theory, the economic order quantity (EOQ) is the
A. Lot size corresponding to break even analysis
B. Average level of inventory
What is the correct answer?
4
Stainless steel is welded with difficulty because of
A. Its high melting temperature
D. Chromium carbide formation
What is the correct answer?
4
The activity of pure hydrogen gas at 1000°C and 5 atm pressure
B. Is always greater than 1
D. Depends on the choice of the standard state
What is the correct answer?
4
What is the value of entropy at 273°K?
What is the correct answer?
4
For which pair of the fuel gases, calorific value (C.V.) of one fuel is almost double that of the other on volume basis (i.e., kcal/Nm3) while the C.V. is same on weight basis (i.e., kcal/kg)?
C. Sewage gas and gobar gas
D. B.F gas and coke oven gas
What is the correct answer?
4
In case of water (Prandtl number ≈ 6) flowing over a flat plate heated over the entire length, the thermal boundary layer thickness as compared to hydrodynamic boundary layer thickness is
What is the correct answer?
4
Spark plug is provided in a/an
A. Engine having carburettor
C. Compression ignition engine