Related Questions
What is the correct answer?
4
Powder metallurgy process does not make metal powder by
D. Electrolytic deposition
What is the correct answer?
4
__________ furnace is generally used in the non-ferrous foundries.
What is the correct answer?
4
__________ property of steel increases by addition of large amount of silicon in it.
What is the correct answer?
4
Particle nature of cathode rays is proved due to the fact that they
A. Travel in a straight line
B. Get deflected by magnetic electric field
D. Heat the exposed material
What is the correct answer?
4
Adhesives
A. Cant be used in the form of pressure sensitive tapes
B. Cant join two dissimilar metals
C. Cure instantaneously after application on a surface
What is the correct answer?
4
Co-efficient of performance of a Carnot cycle refrigerator operating between - 23°C and + 27°C is
What is the correct answer?
4
What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively.
What is the correct answer?
4
In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases.
What is the correct answer?
4
In practice, the compression ratio of compression-ignition (CI) engine ranges from
What is the correct answer?
4
The wet bulb temperature is lower in dry air than in wet air at the same temperature. A dry bulb thermometer registers a higher temperature than a wet bulb thermometer except at __________ percent relative humidity.
What is the correct answer?
4
Which of the following is the largest quantum of pressure?
What is the correct answer?
4
Principal alloying element in Elinvar (used for making hair springs for watches) is
What is the correct answer?
4
The dimensional formula of bulk modulus of elasticity is same as that of the
What is the correct answer?
4
A psychrometer does not measure the __________ temperature of moist air.
What is the correct answer?
4
Increase in temperature, in general results in the
A. Decrease in the viscosities of both liquids & gases
B. Increase in the viscosities of both liquids & gases
C. Increase in the viscosity of liquids and decrease in that of gases
D. Decrease in the viscosity of liquids and increase in that of gases
What is the correct answer?
4
A material being tested for endurance strength is subjected to the __________ load.
What is the correct answer?
4
Corrosion rate cannot be lowered by reducing the __________ of the corroding medium.
What is the correct answer?
4
Which of the following is not a charge material for cupola?
What is the correct answer?
4
Pick out the wrong statement.
A. Copper is the metal having the highest electronic conductivity
B. Hardenability & Weldability of metals are inversely related
C. Covalent bonding formed by sharing of electrons is present in all semi-conductor materials
D. Glass transition temperature applies to 'polymers' but not to 'glasses'
What is the correct answer?
4
X-rays are
D. Of higher wavelength than visible light
What is the correct answer?
4
The most important consideration in value engineering is the
What is the correct answer?
4
In the formation of cermets, the ratio of ceramic material to metallic material is usually 80:20. Which of the following is a cermet?
What is the correct answer?
4
__________ metal is used as a bearing liner material.
What is the correct answer?
4
Silicon crystal can be converted to p-type semiconductor by doping with
What is the correct answer?
4
Primary designation of steel is based on its
A. Hardness & tensile strength
D. Alloying elements content
What is the correct answer?
4
Solidification time of a molten metal in a casting is proportional to (where, V = volume of metal & A = its surface area; in the casting)
What is the correct answer?
4
Exposure to __________ accelerates the degradation of plastics.
B. High atmospheric temperature
C. High ambient temperature
What is the correct answer?
4
Transition from laminar flow to turbulent flow in fluid flow through a pipe does not depend upon the
What is the correct answer?
4
Cold working of a material results in increase in hardness, which is termed as the __________ hardening.
What is the correct answer?
4
Out of the following the refractive index is the highest for