Related Questions
What is the correct answer?
4
Coating provided on the electrodes used in the arc welding is not expected to
B. Prevent electrode from contamination
D. Provide protective atmosphere to weld
What is the correct answer?
4
The best lubricants for a machine working at high temperature & load is
What is the correct answer?
4
Cast iron contains __________ percent carbon.
What is the correct answer?
4
Alumina, silica, lime and iron oxide are the basic raw material for the manufacture of Portland cement. The component of Portland cement which first hardens is
What is the correct answer?
4
In __________ process, there is an increase in entropy with no degradation of energy.
B. Isochoric heat addition
D. Isobaric heat addition
What is the correct answer?
4
The activity of pure hydrogen gas at 1000°C and 5 atm pressure
B. Is always greater than 1
D. Depends on the choice of the standard state
What is the correct answer?
4
Blast furnace slag is mainly molten
What is the correct answer?
4
The noble metals
A. Are exemplified by Na, K and Li
B. Do not resist corrosion very strongly
C. Are the lowermost in the electro-chemical series of metals
What is the correct answer?
4
Out of the following, the best material capable of withstanding shock & vibration without the danger of cracking is
What is the correct answer?
4
A common disinfectant used in village wells for disinfection of water is
D. Potassium permanganate
What is the correct answer?
4
To counteract the bad effects of strain hardening on a cold formed part, it must be
What is the correct answer?
4
Encyclopaedia of Chemical Technology has been
A. Authored by Kirk Othmer
B. Edited by Perry and Chilton
D. Authored by Perry and Chilton
What is the correct answer?
4
Which of the following is not a dielectric material?
A. Cotton, silk and paper
B. Asbestos, glass, porcelain and mica
C. Rubber and polymeric resins
D. All refractory materials
What is the correct answer?
4
The 'transition temperature' for ductile to brittle behaviour of steel increases with increase in the __________ content in steel.
What is the correct answer?
4
Boiler draught of 10 mm water column is equivalent to
What is the correct answer?
4
Production of one ton of paper in Indian paper industry consumes about __________ kWh of electricity.
What is the correct answer?
4
Baffles provided on the shell side of a shell and tube heat exchanger are meant for
A. Providing support for the tubes
B. Improving heat transfer
D. Preventing the fouling of tubes & stagnation of shell side fluid
What is the correct answer?
4
__________ has the highest melting point out of the following.
What is the correct answer?
4
Brazing is the joining of metals
A. Without melting the base metal
B. With a non-ferrous filler
What is the correct answer?
4
Depreciation of machines fails under the indirect expenses head. As per income tax regulations, it is calculated by the __________ method.
C. Multiple straight line
D. Sum of the years digit
What is the correct answer?
4
Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2 .k), when the insulation thickness is __________ mm.
What is the correct answer?
4
Lead is poured into the joint between two- __________ pipes.
What is the correct answer?
4
Capacity & power requirement for an air compressor working at high altitude compared to sealevel will be
D. Either more or less; depends on the climatic conditions
What is the correct answer?
4
The substance used as a smoke screen in warfare is
What is the correct answer?
4
An alloy of Fe - 0.4 % C is
What is the correct answer?
4
With increase in compression ratio, the volumetric efficiency of air compressor
D. May increase or decrease (depends on the suction pressure)
What is the correct answer?
4
Oxide layer formed on the non-ferrous metal surface after its annealing is
A. Removed by acid pickling
B. Hammered into the surface
C. Removed with coarse emery cloth
D. Left as such to protect the surface
What is the correct answer?
4
In a good rimming steel
A. Carbon and silicon should be low
B. Silicon should be low but carbon should be high
C. Both silicon & carbon should be high
D. Silicon should be high but carbon should be low
What is the correct answer?
4
With increase in impurities in metals, their corrosion resistances
D. May increase or decrease; depending on the type of metal
What is the correct answer?
4
Titanium is added to molten aluminium alloys before casting for the purpose of
B. Increasing corrosion resistance