Related Questions
What is the correct answer?
4
Ammonia gas can be dried by
What is the correct answer?
4
Water flow in the river during flood can be categorised as the __________ flow.
What is the correct answer?
4
Which of the following phenomenon/ phenomena is/are diffusion controlled?
What is the correct answer?
4
Sand used to stop the green sand from sticking to the pattern is termed as the __________ sand.
What is the correct answer?
4
Suitability of steel for its use in cable is judged by its strength in
What is the correct answer?
4
Maximum consumption of limestone is in the __________ industry.
What is the correct answer?
4
A pycnometer is used for the measurement of
A. Flow rate of molten metal
B. Specific gravity of a liquid
D. Concentration of a solution
What is the correct answer?
4
Pick out the wrong statement.
A. Seam welding, projection welding & spot welding are the classification of electrical resistance welding
B. Electrode tip in spot welding is of copper and the tip diameter should be equal to t (where, t = plate thickness to be welded)
C. In spot welding, two pieces to be joined are overlapped and placed between two electrodes
D. Mild steel sheet cannot be spot welded
What is the correct answer?
4
Oxyacetylene reducing flame is used while carrying out welding on
What is the correct answer?
4
Which of the following terminology is used for the temperature at which new grains are formed in a metal?
B. Lower critical temperature
C. Recrystallisation temperature
D. Upper critical temperature
What is the correct answer?
4
Maximum amount of thermal radiation is emitted at all wavelengths at any specified temperature by a/an __________ body.
What is the correct answer?
4
Maraging steels derive their strength from the following mechanism:
A. A fine, highly dislocated and strong martensite
B. Fine dispersions of inter-metallic of Fe, Ni, Ti etc
C. Fine dispersions of alloy carbides in a ferrite matrix
D. Fine dispersions of C nucleated on dislocations in austenite
What is the correct answer?
4
Midrex process of sponge iron production uses reformed natural gas as the reducing agent, which uses iron ore in the form of
What is the correct answer?
4
Hollow shafts can be made as strong as solid shafts by making the twisting moments of both the shafts same. Shafts made by __________ have residual stresses.
What is the correct answer?
4
For a first order chemical reaction, the concentration of the reactant decreases __________ with time.
What is the correct answer?
4
High relative humidity decreases the evaporative process and as the temperature is increased, the relative humidity decreases. The comfort range for human body is the ambient temperature of 22 to 27°C with relative humidity ranging from __________ percent.
What is the correct answer?
4
__________ pipe is the most suitable for carrying sanitary drainage.
B. Reinforced cement concrete
What is the correct answer?
4
Minimum number of members required to form a Public Limited Joint Stock Com-pany is
What is the correct answer?
4
Powder metallurgy is used to produce
A. High precision components with complex cavities and sharp features
B. Components of large size
C. Porosity free components
D. Components of such alloys whose constituents do not form alloys readily
What is the correct answer?
4
Which of the following is not a principal alloying element for the structural steel?
What is the correct answer?
4
For preparation of porous bearings by powder metallurgy, preferred particle shape is
What is the correct answer?
4
Vernier calipers cannot be used to measure the
A. I.D. & O.D. of the shaft
D. Clearance between two mating surfaces
What is the correct answer?
4
The hardenability of steel decreases with
A. Decrease in dislocation density
B. Increase in solutionising temperature
D. Decrease in grain size
What is the correct answer?
4
A material being tested for endurance strength is subjected to the __________ load.
What is the correct answer?
4
In electrical resistance welding, distortion results from the use of improper
What is the correct answer?
4
Friction factor for fluid flow in pipe does not depend upon the
C. Fluid density & viscosity
D. Mass flow rate of fluid
What is the correct answer?
4
Silicon percentage in acid resistant cast iron is about
What is the correct answer?
4
The following type of bonding is strongly directional in solids.
What is the correct answer?
4
Corrosion rate cannot be lowered by reducing the __________ of the corroding medium.
What is the correct answer?
4
Most of the phosphorous present in the blast furnace burden enters into