Related Questions
What is the correct answer?
4
The rolling process cannot be used to produce
What is the correct answer?
4
Cold heading or upsetting is categorised as the __________ process.
What is the correct answer?
4
For efficient performance of a blast furnace, the extent of reduction of Wustite (FeO) should be
A. 100% indirect reduction
C. 50-60% indirect reduction
D. 30-40% indirect reduction
What is the correct answer?
4
Wrought iron is never shaped by
What is the correct answer?
4
A semi-conductor is damaged & behaves like a conductor, on passing a strong electric current through it, because it heats up the crystals & breaks the covalent bonds resulting in __________ electrons.
What is the correct answer?
4
Nusselt number/Biot number varies
A. Inversely with thermal conductivity
B. Directly with heat transfer co-efficient
C. Directly with thermal conductivity
D. Inversely with the dimension of the solid
What is the correct answer?
4
The expected efficiency of a single riveted lap joint is of the order of 50%. If the thickness of the plate is increased four times, then the rivet diameter will have to be increased __________ times.
What is the correct answer?
4
Air-petrol ratio for maximum power generation in spark ignition engine is about
What is the correct answer?
4
Dislocations are __________ defects.
What is the correct answer?
4
Unit of surface tension in S.I. unit is
B. Joule/
C. Newton/
What is the correct answer?
4
The same volume of all gases is representative of their
C. Gas characteristic constants
What is the correct answer?
4
Dislocation cross-slip is difficult in those materials, which have
A. Large number of slip systems
B. High work hardening rate
D. Low stacking fault energy
What is the correct answer?
4
The maximum thickness of the metal which can be welded using ultrasonic welding is __________ mm.
What is the correct answer?
4
Upto the critical radius of insulation, added insulation, will
A. Increase the heat loss
B. Decrease heat loss and will have no effect beyond that
D. Reduce convection heat loss compared to conduction heat less
What is the correct answer?
4
Sub zero treatment of steel is done to
A. Suppress martensite transformation
B. Enhance its working performance in sub zero atmosphere
C. Reduce the retained austenite in hardened steel
D. Induce temper brittleness after its hardening
What is the correct answer?
4
Starting friction is low in case of the __________ lubrication.
What is the correct answer?
4
Titanium is produced by __________ of Ti Cl4.
A. Electrolytic reduction
What is the correct answer?
4
On oscilloscope screen for dynamic measurement, lissajous diagram is normally used to determine the __________ of the input signal.
What is the correct answer?
4
A particle is settling in a liquid under Stokesian conditions. The free falling velocity of the particle is proportional to
What is the correct answer?
4
'GASOHOL' widely used in Brazil as a motor fuel is a mixture of alcohol and
C. Light hydrocarbon gases (e.g. butane or propane)
What is the correct answer?
4
Temper brittleness of a material can be fairly detected by the __________ test.
What is the correct answer?
4
What is the value of included angle of a triangular notch for maximum discharge?
What is the correct answer?
4
__________ circuit is most commonly used to measure strain with the help of a strain gauge.
B. Voltage balancing potentiometric
C. Simple current sensitive
What is the correct answer?
4
Screws are specified by their __________ diameters.
What is the correct answer?
4
Limestone is added in the blast furnace (during pig iron manufacture) to
A. Form slag by combining with impurities
B. Supply heat by undergoing exothermic reaction with impurities
C. Reduce the coke consumption
What is the correct answer?
4
Window panes of aeroplanes are normally made of
C. Bakelite (phenol formaldehyde)
What is the correct answer?
4
The specific gravity of coal depends mainly on its __________ content.
What is the correct answer?
4
Thermal diffusivity of a substance is proportional to (where, k = Thermal conductivity)
What is the correct answer?
4
Often earing defects are found during deep drawing operation, because the
A. Surface finish of the sheet is poor
B. Sheet material has been given substantial spring back
C. Starting sheet has planer anisotropy due to its texture
D. Starting sheet has normal anisotropy due to its texture
What is the correct answer?
4
Filler material used in welding should have __________ as compared to the parent metal to be welded.
A. Lower melting temperature
B. Same melting temperature