Related Questions
What is the correct answer?
4
The atmospheric temperature during melting of ice/snow (in the atmosphere)
D. May increase or decrease; depends on the altitude where snow melts
What is the correct answer?
4
Use of flux during soldering is done to
A. Increase fluidity of solder by lowering its melting temperature
B. Prevent oxide formation
C. Wash away surplus solder
What is the correct answer?
4
Cast iron contains __________ percent carbon.
What is the correct answer?
4
Steel containing low percentage of nickel, chromium & tungsten are termed as the __________ steel.
What is the correct answer?
4
In the acid Bessemer process, the hot metal should have the following composition.
A. S < 0.05% and P < 0.05%
B. S < 0.05% and P < 1.5%
C. S < 0.05% and P > 1.5%
D. S > 1.5% and P < 0.05%
What is the correct answer?
4
The elastic strain energy of a unit length of an edge dislocation as compared to that of a screw dislocation is
What is the correct answer?
4
Limestone is added in the blast furnace (during pig iron manufacture) to
A. Form slag by combining with impurities
B. Supply heat by undergoing exothermic reaction with impurities
C. Reduce the coke consumption
What is the correct answer?
4
The softness or hardness of a grinding wheel depends upon the type & amount of bonding material used. For general purpose cutter grinding __________ grinding wheel is normally used.
What is the correct answer?
4
Dryness fraction of dry steam is
What is the correct answer?
4
Leakage in a cooking gas cylinder is detected by
B. Pouring soap solution on the surface and locating the gas bubbles
D. Pungent smell of mercaptans present in the gas
What is the correct answer?
4
Specific gravity of hot metal (pig iron) is __________ times that of the blast furnace slag.
What is the correct answer?
4
Other parameters remaining same, the recrystallisation temperature of an alloy is lowered, when
A. Strain rate is increased
B. Grain size is increased
C. Prior cold deformation is increased
D. Not affected by any of the above parameters
What is the correct answer?
4
Which of the following relationships is correct for relating the three elastic constants of an isotropic elastic material (where, E = Young's modulus, G = Modulus of rigidity or shear modulus v = Poisson's ratio)?
What is the correct answer?
4
The best lubricants for a machine working at high temperature & load is
What is the correct answer?
4
Powder metallurgy process does not make metal powder by
D. Electrolytic deposition
What is the correct answer?
4
Boiler tube size is specified by its thickness and __________ diameter.
What is the correct answer?
4
Production of a hollow product by inflation of a tube or parison is called the __________ process.
What is the correct answer?
4
Which of the following rays has the least wavelength?
What is the correct answer?
4
The order of a chemical reaction
A. Can be determined only experimentally
B. Can be determined from the stoichiometry of the reaction
What is the correct answer?
4
Addition of small amount of __________ to grey cast iron is done to produce nodular grey cast iron.
What is the correct answer?
4
The noble metals
A. Are exemplified by Na, K and Li
B. Do not resist corrosion very strongly
C. Are the lowermost in the electro-chemical series of metals
What is the correct answer?
4
Removal of non-condensable from steam or other vapour is termed as the __________ process.
What is the correct answer?
4
Compressed dry air is used as the cutting fluid, while machining
What is the correct answer?
4
Pick out the wrong statement.
A. Seam welding, projection welding & spot welding are the classification of electrical resistance welding
B. Electrode tip in spot welding is of copper and the tip diameter should be equal to t (where, t = plate thickness to be welded)
C. In spot welding, two pieces to be joined are overlapped and placed between two electrodes
D. Mild steel sheet cannot be spot welded
What is the correct answer?
4
The product of a commercial direct reduction process is
D. Iron saturated with carbon
What is the correct answer?
4
In TIG welding, thoriated tungsten electrodes are used, because it
A. Has higher current carrying capacity
B. Has better electron emissivity
C. Is stronger than ordinary tungsten
What is the correct answer?
4
Consumable electrodes are used in the __________ welding.
What is the correct answer?
4
Gage pressure within a spherical droplet of a fluid is 'p'. What will be gage pressure within a bubble of the same size & of the same fluid?
What is the correct answer?
4
Which of the following is not categorised as the ore agglomeration process?
What is the correct answer?
4
Filler material used in welding should have __________ as compared to the parent metal to be welded.
A. Lower melting temperature
B. Same melting temperature