Related Questions
What is the correct answer?
4
Newer versions of Auto-CAD utilize the ________ to make block library management very easy.
What is the correct answer?
4
Architectural dimensioning is usually done in ________.
What is the correct answer?
4
Acceptable parts must not extend beyond this:
What is the correct answer?
4
These drawings are given to contractors to perform work or manufacture individual parts:
What is the correct answer?
4
This is the range of digital or hard copy documents that specify the physical function requirements for a product:
What is the correct answer?
4
This is the bottom surface joining the sides of two adjacent threads:
What is the correct answer?
4
The 3-D commands on the Modeling toolbar include ________.
What is the correct answer?
4
When the drafter types the word BLOCK or selects the Make Block tool from the Draw tool bar the ________ will appear.
C. Block Definition Dialog
What is the correct answer?
4
In isometric projection, all distances are approximately this percentage of their true size:
What is the correct answer?
4
This type of solid has two bases that are parallel equal polygons:
What is the correct answer?
4
The principle views associated with orthographic projection are ________.
What is the correct answer?
4
Technical drawings typically serve one of three purposes:
A. Visualization, Communication, or Documentation
B. Visualization, Dimensioning, or Documentation
C. Communication, Documentation, or Installation
D. Documentation, Installation, or Engineering
What is the correct answer?
4
Referring to the fractional inches to decimal inches to millimetre conversion chart on page 55 what is the equivalent mm measurement of 3/16 inch.
What is the correct answer?
4
When setting up a mechanical drawing in Auto-CAD the drafter should set the units to ________.
What is the correct answer?
4
In U.S. structural and architectural drafting, all dimensions of this length are usually expressed in feet and inches:
What is the correct answer?
4
The Free Orbit tool is found on the ________ toolbar.
What is the correct answer?
4
To insure that everyone understands what the electrical symbols represent it is customary to include a ________ on the electrical sheet.
What is the correct answer?
4
In a CAD system, you can draw an ellipse by specifying these:
B. The midpoint and end points
C. The center and major and minor axes
What is the correct answer?
4
This type of auxiliary view is projected onto a plane that is perpendicular to one of the principal planes of projection:
What is the correct answer?
4
This is a solid shape that fits inside the mold and forms a hole in a cooled cast metal or molten plastic object:
What is the correct answer?
4
The Press-Pull tool will ________ the face of a solid model in the direction it faces.
What is the correct answer?
4
Using the Relative Polar Coordinate System to add a 3 inch line that is 45 degrees from the end point of the line created above the drafter would ________.
B. Type 3 back slash and enter
C. Type 3 forward slash and enter
D. Type 3 and try to use the Dynamic Input readout to find the end point
What is the correct answer?
4
The architectural drafter usually begins a set of working drawings by creating the ________ plan first.
What is the correct answer?
4
This type of surface is tipped to all principal planes of projection and does not appear true size in any standard view:
What is the correct answer?
4
The dimension text size is determined by what the architect deems necessary in __________.
What is the correct answer?
4
An architect often relies on a ________ to complete the set of technical drawings used in the design of an office building.
D. Construction superintendent
What is the correct answer?
4
Spur gear design normally begins with selecting this:
What is the correct answer?
4
When lettering a CAD drawing, for clarity you should limit the number of fonts to:
What is the correct answer?
4
Traditional drafters need to be able to create several different line widths because ________.
A. Different line widths convey different information
B. The line width has to do with how dark it appear in the finished drawing
C. They seem to transmit better in a fax machine
D. It makes no difference
What is the correct answer?
4
A back or backing weld is a type of: