When creating an isometric drawing in Auto-CAD the drafter can utilize the Dynamic Input and Polar Coordinate system to place both vertical and horizontal lines. A line created from one point 3 inches at 180 degrees would be a ________ line.
Horizontal
Vertical
Inclined
None of the above
Correct Answer :
B. Vertical
Related Questions
EDM is the acronym for:
Enterprise data management
Engineering drawing management
Enterprise drawing manipulation
Engineering data manipulation
A ________ section allows the drafter to create a Cutting Plane line which is not in a straight line across the part.
Offset
Half
Whole
Broken out
In this type of auxiliary view, a break line is used to indicate the imaginary break in the views:
Primary
Secondary
Revolved
Partial
How can the drafter prevent Auto-CAD from placing or stacking another center mark on a circle when adding a diameter dimension to it?
Explode the dimension and then erase the center mark
Use the Properties dialog box to turn off the center mark of the dimension
It can't be done
Use the trim tool to take away the stacked center mark
The standard number of threads per inch for various diameters is the:
Series of thread
Lead
Major diameter
Thread pitch
This means that a feature of a finished product contains the maximum amount of material permitted by the tolerance dimensions for that feature:
Maximum material condition
Machined material condition
Maximum machined indication
Machine mark indication
Most architectural firms and mechanical design companies utilize different categories of blocks. These sets of blocks are usually housed in ________.
Block vaults
Block libraries
Block books
Block references
This is how axonometric, oblique, and perspective sketches show objects:
Orthographically
Pictorially
Obliquely
Parallel
Architectural drawings used to construct a house are often plotted with a scale of ¼ = 1'-0. What scale is this?
Quarter
Half
Full
Double
When using the direct entry method to create a horizontal line exactly three inches long the drafter should ________ first.
Pull the line from away from the starting point very carefully
Insure that Ortho is on
Enter 3 for the length of the line
Read the coordinate position on the Dynamic Readout
The text used on a typical detail sheet should be ________.
Placed horizontally
In bold text
In an architectural text style
None of the above
The offset distance for the width (front to back) distance of the auxiliary view is the same distance of the ________ in the top view.
Width
Height
Length
None of the above
This is a rounded exterior blend between surfaces:
Fillet
Round
Taper
Chamfer
In order to set drawing limits for a C size architectural drawing the drafter should set the limits to ________.
0, 0 and 2, 9
0, 0 and 17, 11
0, 0 and 18, 24
0, 0 and 34, 24
A line with a tapering width can be easily created by using the __________ tool.
Circle
Ellipse
Line
Polyline
Lines of an isometric drawing that are not parallel to the isometric axes are called this:
Trimetric lines
Non-isometric lines
Multiview lines
Dimetric lines
An engineer's scale would be used to measure lines on a drawing where the scale factor reads ________.
1/4 = 1'-0
1/8 = 1'-0
1 = 100'
3/4 = 1'-0
In this type of view, the cutting plane line indicates both the location of the cutting plane and the direction of sight:
Removed section
Revolved section
Auxiliary section
Partial section
In this type of concrete, the steel is pre-tensioned before the superimposed load is applied:
Aggregate
Pre-stressed
Reinforced
Preloaded
Placement of dimensions on a drawing is controlled by ________.
ANSI
The design engineer
Corporate drafting standards
All of the above
Switches and relays should be shown in this position with no operating force or applied energy:
Normal
Closed
Offset
Application
This type of surface may be a plane, a single curved surface, or a warped surface:
Edge surface
Ruled surface
Auxiliary surface
Developed surface
The principle views associated with orthographic projection are ________.
Front view
Right side view
Top view
All of the above
In perspective drawings this is placed between the observer and the object:
Vanishing point / horizon
Station point
Ground line
Plane of projection / picture plane
An oil refinery relies on which type of drafter to maintain and update the technical piping drawings used for the construction and maintenance of the facility.
Architectural
Civil
Process piping
Electrical
A projection weld is a type of:
Resistance weld
Arc weld
Gas weld
Fillet weld
An advantage of this type of view is that each view shows the object all the way through as if it were transparent:
Planar
Horizontal
Auxiliary
Orthographic
This allows the performance of structures to be analyzed and tested efficiently, accurately, and quickly:
Computer-aided manufacturing
Computer-aided design
Computer-aided engineering
Computer-aided prototyping
An Auto-CAD term that refers to a pre-drawn object which is stored in a drawing file and can be inserted into any other drawing file as needed is a ________.
Block
Brick
Balloon
None of the above
These are used to attach parts to a cylinder so they won't turn on it:
Lugs and bearings
Key-seats and bearings
Knurls and keys
Keys and keyways/key-seats