Related Questions
What is the correct answer?
4
The working depth of a gear is the radial distance from the
A. Pitch circle to the bottom of a tooth
B. Pitch circle to the top of a tooth
C. Top of a tooth to the bottom of a tooth
D. Addendum circle to the clearance circle
What is the correct answer?
4
A point on a connecting link (excluding end points) of a double slider crank mechanism traces a
What is the correct answer?
4
In vibration isolation system, the transmissibility will be equal to unity, for all values of damping factor, if ω/ωn is
What is the correct answer?
4
The type of pair formed by two elements which are so connected that one is constrained to turn or revolve about a fixed axis of another element is known as
What is the correct answer?
4
The frictional torque transmitted in a conical pivot bearing, considering uniform pressure, is (where R = Radius of shaft, and α = Semi-angle of the cone)
What is the correct answer?
4
A point B on a rigid link AB moves with respect to A with angular velocity ω rad/s. The radial component of the acceleration of B with respect to A, is (where vBA = Linear velocity of B with respect to A)
What is the correct answer?
4
The direction of Coriolis component of acceleration is the direction
A. Of relative velocity vector for the two coincident points rotated by 90° in the direction of the angular velocity of the rotation of the link
B. Along the centripetal acceleration
C. Along tangential acceleration
D. Along perpendicular to angular velocity
What is the correct answer?
4
Which type of gearing is used in steering system of an automobile?
What is the correct answer?
4
The product of the diametral pitch and circular pitch is equal to
What is the correct answer?
4
The frictional torque transmitted in a flat pivot bearing, considering uniform wear, is (where μ = Coefficient of friction, W = Load over the bearing, and R = Radius of bearing surface)
What is the correct answer?
4
When the load on the engine increases, it becomes necessary to increase the supply of working fluid and when the load decreases, less working fluid is required. The supply of the working fluid to the engine is controlled by a
C. Meyer's expansion valve
What is the correct answer?
4
ABCD is a four bar mechanism in which AB = 310 mm and CD = 450 mm. AB and CD are both perpendicular to the fixed link AD, as shown in the below figure. If the velocity of B at this condition is v. Then the velocity of C is
What is the correct answer?
4
If the controlling force line for a spring controlled governor when produced intersects the Y-axis at the origin, then the governor is said to be
What is the correct answer?
4
A cam with a roller follower would constitute following type of pair
What is the correct answer?
4
The maximum velocity of a particle moving with simple harmonic motion is
What is the correct answer?
4
In a circular arc cam with roller follower, the acceleration in any position of the lift will depend only upon
A. Total lift, total angle of lift, minimum radius of cam and cam speed
B. Radius of circular arc, cam speed, location of centre of circular arc and roller diameter
C. Mass of cam follower linkage, spring stiffness and cam speed
D. Total lift, centre of gravity of the cam and cam speed
What is the correct answer?
4
When a point at the end of a link moves with constant angular velocity, its acceleration will have
B. Tangential component only
C. Coriolis component only
D. Radial and tangential components both
What is the correct answer?
4
The face of the tooth is the
A. Surface of the top of tooth
B. Surface of tooth above the pitch surface
C. Width of tooth below the pitch surface
D. Width of tooth measured along the pitch circle
What is the correct answer?
4
The maximum fluctuation of speed is the
A. Difference of minimum fluctuation of speed and the mean speed
B. Difference of the maximum and minimum speeds
C. Sum of maximum and minimum speeds
D. Variations of speed above and below the mean resisting torque line
What is the correct answer?
4
Module of a gear is
What is the correct answer?
4
Which of the following governor is used to drive a gramophone?
What is the correct answer?
4
Which of the following is a spring controlled governor?
C. Wilson-Hartnell governor
What is the correct answer?
4
The critical speed of a shaft with a disc supported in between is equal to the natural frequency of the system in
C. Longitudinal vibrations
What is the correct answer?
4
A rotor which is balanced statically but not dynamically is supported on two bearings L apart and at high speed of the rotor, reaction on the left bearing is R. The right side of the bearing is shifted to a new position 2L apart from the left bearing. At the same rotor speed, dynamic reaction on the left bearing in the new arrangement will
What is the correct answer?
4
The D-slide valve is also known as
A. Inside admission valve
B. Outside admission valve
What is the correct answer?
4
The example of higher pair is
A. Belt, rope and chain drives
C. Ball and roller bearings
What is the correct answer?
4
Angle of action of cam is defined as the angle
A. Of rotation of the cam for a definite displacement of the follower
B. Through which the cam rotates during the period in which the follower remains in the highest position
C. Moved by the cam from the instant the follower begins to rise, till it reaches its highest position
D. Moved by the cam from beginning of ascent to the termination of descent
What is the correct answer?
4
A friction circle is a circle drawn when a journal rotates in a bearing. Its radius depends upon the coefficient of friction and the
A. Magnitude of the forces on journal
B. Angular velocity of journal
C. Clearance between journal and bearing
What is the correct answer?
4
An automobile steering gear is an example of
What is the correct answer?
4
The contact ratio for gears is