When the shear angle is large
Path of shear is short and chip is thin
Path of shear is large and chip is thick
Path of shear is short and chip is thick
Path of shear is large and chip is thin
Correct Answer :
A. Path of shear is short and chip is thin
Related Questions
The machining of titanium is difficult due to
High thermal conductivity of titanium
Chemical reaction between tool and work
Low tool-chip contact area
None of these
A __________ grinding wheel is used to grind soft materials.
Course grained
Medium grained
Fine grained
None of these
Ceramic tools are fixed to tool body by
Soldering
Brazing
Welding
Clamping
A CNC vertical milling machine has to cut a straight slot of 10 mm width and 2mm depth by a cutter of 10 mm diameter between points (0,0) and (100,100) on the XY plane (dimensions in mm). The feed rate used for milling is 50 mm/min, milling time for the slot (in seconds) is
120
170
180
240
The material property which depends only on the basic crystal structure is
Fatigue strength
Work hardening
Fracture strength
Elastic constant
In an interchangeable assembly, shafts of size 25.000 -0.0100⁺⁰⁰⁴⁰ mm mate with holes of size 25.000 -0.010⁺⁰⁰²⁰ mm. The maximum possible clearance in the assembly will be
10 microns
20 microns
30 microns
60 microns
The carbide tools operating at very low cutting speeds (below 30 m/min)
Reduces tool life
Increases tool life
Have no effect on tool life
Spoils the work piece
The specific cutting energy used for establishing the machinability of the metal depends upon its
Coefficient of friction
Microstructure
Work hardening characteristics
All of these
Two 1 mm thick steel sheets are to be spot welded at a current of 5000 A. Assuming effective resistance to be 200 μm and current flow time of 0.2 second, heat generated during the process will be
0.2 Joule
1 Joule
5 Joule
1000 Joule
Dielectric is used in
Electrochemical machining
Ultrasonic machining
Electro discharge machining
Laser machining
The object of caulking in a riveted joint is to make the joint
Free from corrosion
Stronger in tension
Free from stresses
Leak-proof
The depth of cut in drilling is __________ the drill diameter.
Equal to
One-fourth
One-half
Double
In which of the following machine, the work is usually rotated while the drill is fed into work?
Sensitive drilling machine
Radial drilling machine
Gang drilling machine
Deep hole drilling machine
In order to have interference fit, it is essential that the lower limit of the shaft should be
Greater than the upper limit of the hole
Lesser than the upper limit of the hole
Greater than the lower limit of the hole
Lesser than the lower limit of the hole
The factor which affects the tool life is
Tool geometry
Cutting speed
Feed rate
All of these
A bottoming tap has
Its end tapered for about three or four threads
Its end tapered for about eight or ten threads
Full threads for the whole of its length
None of the above
The cutting fluid mostly used for machining alloy steels is
Water
Soluble oil
Dry
Sulphurised mineral oil
In metal machining, the zone where the heat is generated due to friction between the moving chip and the tool face, is called
Friction zone
Work-tool contact zone
Shear zone
None of these
A grinding wheel becomes glazed (i.e. cutting edge takes a glasslike appearance) due to
Wear of bond
Breaking of abrasive grains
Wear of abrasive grains
Cracks on grinding wheel
In a gating system, the ratio 1: 2: 4 represents
Sprue base area: runner area: ingate area
Pouring basin area: ingate area: runner area
Sprue base area: ingate area: casting area
Runner area: ingate area: casting area
A drill mainly used in drilling brass, copper or softer materials, is
Flat drill
Straight fluted drill
Parallel shank twist drill
Tapered shank twist drill
Green sand mould indicates that
Polymeric mould has been cured
Mould has been totally dried
Mould is green in colour
Mould contains moisture
Cast iron during machining produces
Continuous chips
Discontinuous chips
Continuous chips with built-up edge
None of these
For softer materials, the point angle of the drill is kept
Equal to 118°
Less than 118°
More than 118°
Any one of these
The saw milling is an operation of
Producing grooves around the periphery of a cylindrical or conical workpiece
Producing narrow slots or grooves on a workpiece
Reproduction of an outline of a template on a workpiece
Machining several surfaces of a workpiece simultaneously
The taper on the lathe spindle is
1 in 10
1 in 15
1 in 20
1 in 30
Stellite preserves hardness upto a temperature of
350°C
500°C
900°C
1100°C
The process of removing metal by a cutter which is rotated in the same direction of travel of workpiece, is called
Up milling
Down milling
Face milling
End milling
In a single point tool, the angle between the surface of the flank immediately below the point and a line drawn from the point perpendicular to the base, is known as
Side relief angle
End relief angle
Back rake angle
Side rake angle
A 15 mm drilling machine means that it can drill a hole
Of maximum diameter 15 mm
In 15 mm thick plates
Having cross-sectional area of 15 mm²
None of these