Related Questions
What is the correct answer?
4
If an application calls for stresses on screw threads in one direction only, then the following type of thread would be best suited
What is the correct answer?
4
Two shafts A and B under pure torsion are of identical length and identical weight and are made of the same material. The shaft A is solid and the shaft B is hollow. We can say that
A. Shaft B is better than shaft A
B. Shaft A is better than shaft B
C. Both the shafts are equally good
What is the correct answer?
4
Stress concentration factor is defined as the ratio of
A. Maximum stress to the endurance limit
B. Nominal stress to the endurance limit
C. Maximum stress to the nominal stress
D. Nominal stress to the maximum stress
What is the correct answer?
4
The centre to centre distance between two consecutive rivets in a row, is called
What is the correct answer?
4
Stress concentration is caused due to
A. Variation in properties of material from point to point in a member
B. Pitting at points or areas at which loads on a member are applied
C. Abrupt change of section
What is the correct answer?
4
Screws used for power transmission should have
What is the correct answer?
4
The design of pin of a rocker arm of an I.C. engine is based on
What is the correct answer?
4
The distribution of the forces along the length of key fitted in a shaft
C. Varies exponentially, being more near the torque-input end
D. Varies exponentially, being less near the torque-input end
What is the correct answer?
4
Two helical springs of the same material and of equal circular crosssection, length and number of turns, but having radii 80 mm and 40 mm, kept concentrically (smaller radius spring within the larger radius spring), are compressed between two parallel planes with a load W. The inner spring will carry a load equal to
What is the correct answer?
4
Which of the following key is preferred for the condition when a large amount of impact type torque is to be transmitted in both direction of rotation?
What is the correct answer?
4
According to Indian standards, the diameter of rivet hole is made larger than the basic size of rivet by
A. 0.5 mm upto rivet diameter of 24 mm
B. 1 mm for rivet diameter from 27 mm to 36 mm
C. 2 mm for rivet diameter from 39 mm to 48 mm
What is the correct answer?
4
If T is the actual number of teeth on a helical gear and φ is the helix angle for the teeth, then formative number of teeth is written as
What is the correct answer?
4
According to Indian standards, total numbers of fundamental deviations are
What is the correct answer?
4
The connecting rod bolts are tightened up with initial tension greater than the external load so that
B. Bolts are weakest elements
C. The resultant load on the bolt would not be affected by the external cyclic load
D. Bolts will not loosen during service
What is the correct answer?
4
A shaft is subjected to a maximum bending stress of 80 N/mm² and maximum shearing stress equal to 30 N/mm² at a particular section. If the yield point in tension of the material is 280 N/mm² and the maximum shear stress theory of failure is used, then the factor of safety obtained will be
What is the correct answer?
4
A bolt of M 24 × 2 means that
A. The pitch of the thread is 24 mm and depth is 2 mm
B. Cross-sectional area of the threads is 24 mm²
C. The nominal diameter of bolt is 24 mm and pitch is 2 mm
D. The effective diameter of bolt is 24 mm and there are 2 threads per cm
What is the correct answer?
4
The rated life of a bearing varies
B. Inversely as square of load
C. Inversely as cube of load
D. Inversely as fourth power of load
What is the correct answer?
4
If a spring is cut down into two springs, the stiffness of cut springs will be
What is the correct answer?
4
At low temperatures (say 75°C) the notched bar impact value of steel
D. Depends on heat treatment carried out
What is the correct answer?
4
According to I.B.R., the efficiency of a double riveted butt joint with double cover straps of equal width should be
What is the correct answer?
4
A screw is said to be over hauling screw, if its efficiency is
What is the correct answer?
4
The pipe joint mostly used for pipes carrying water at low pressures is
D. Spigot and socket joint
What is the correct answer?
4
When carbon in the cast iron is principally in the form of graphite, the cast iron will be of
What is the correct answer?
4
The piston pin bearings in heavy duty diesel engines are
A. Needle roller bearings
B. Tapered roller bearings
C. Spherical roller bearings
D. Cylindrical roller bearings
What is the correct answer?
4
Which of the following has threads at both ends?
What is the correct answer?
4
A bolt is designed on the basis of __________ with a large factor of safety.
B. Direct compressive stress
What is the correct answer?
4
Taper usually provided on cotter is
What is the correct answer?
4
If d is the normal diameter of a bolt in mm, then the initial tension in kg in a bolt used for making a fluid tight joint as for steam engine cover joint is calculated by the relation
What is the correct answer?
4
The angle of twist of shaft is
A. Directly proportional to (shaft diameter)²
B. Inversely proportional to (shaft diameter)²
C. Directly proportional to (shaft diameter)⁴
D. Inversely proportional to (shaft diameter)⁴
What is the correct answer?
4
The edges of a boiler plate are bevelled to an angle of