Related Questions
What is the correct answer?
4
You have a total of five routers. ________ circuits are required to fully mesh the network, where every router needs ___________ interfaces.
What is the correct answer?
4
You have ISL trunks in your network and five VLANs configured. How many instances of STP are running?
What is the correct answer?
4
During the learning function, the switch places addresses and ports in a(n) _________ table.
What is the correct answer?
4
A __________ topology uses a single connection to connect all devices together.
What is the correct answer?
4
You are at User EXEC mode and type the letter e. What message appears?
C. % Unknown command or computer name
D. % Invalid input detected at '^'.
What is the correct answer?
4
RIP supports load balancing for up to __________ ___________ paths.
What is the correct answer?
4
You are given the following addressing information: 172.17.16.255/23. What type of address is this?
What is the correct answer?
4
VLSM allows you to summarize __________ back to the class boundary.
What is the correct answer?
4
172.16.240.256 is a class __________ address.
What is the correct answer?
4
When choosing a WAN solution, consider all of the following except __________.
What is the correct answer?
4
What router command saves the active configuration to NVRAM?
A. copy nvram startup-config
B. copy startup-config running-config
C. copy running-config nvram
D. copy running-config startup-config
What is the correct answer?
4
________ topologies in NBMA environments do not have problems with split horizon.
What is the correct answer?
4
The ___________ converts an ISDN four-wire connection to a two-wire connection.
What is the correct answer?
4
_________ defines how the Frame Relay DTE and DCE interact with each other.
What is the correct answer?
4
Which command defines interesting traffic?
What is the correct answer?
4
On the 1900 switch, how do you enter User EXEC mode?
A. It comes up by default.
B. Enter the letter U in the menu.
C. Enter the letter K in the menu.
D. Enter the letter C in the menu.
What is the correct answer?
4
Which router command would you use to test only layer-3 connectivity?
What is the correct answer?
4
Which of the following is true concerning bridges?
A. They switch frames in hardware.
B. They support half- and full-duplexing.
C. They support one collision domain for the entire bridge.
D. They do only store-and-forward switching.
What is the correct answer?
4
An idle DDR connection will be torn down after _________ seconds of not seeing interesting traffic.
What is the correct answer?
4
Which type of routing protocol uses the Shortest Path First algorithm?
What is the correct answer?
4
When examining the IP routing table, an EIGRP route will be shown as what letter?
What is the correct answer?
4
A 1924 has _________ Ethernet interfaces.
What is the correct answer?
4
What command creates a DHCP address pool on a router?
What is the correct answer?
4
You are given a class C network and you have four LAN segments with the following numbers of devices: 120, 60, and two with 30. What subnet mask values would you use to accommodate these segments?
What is the correct answer?
4
When connecting a switch to a router, use a ___________ cable.
What is the correct answer?
4
If you wanted a list of parameters for the show command, you would type ________.
What is the correct answer?
4
Which types of memory do not maintain their contents during a power-off state?
What is the correct answer?
4
Which is an example of a hybrid protocol?
What is the correct answer?
4
You are given a class C network, 192.168.1.0/24. You need three networks with 60 hosts and two networks with 30 hosts. What are the subnet mask values you could use?
A. 255.255.255.128 and 255.255.255.192
B. 255.255.255.224 and 255.255.255.240
C. 255.255.255.192 and 255.255.255.224
What is the correct answer?
4
The 1900 switch supports ________ VLANs.