Which of the following commands belongs on the physical interface when using dialer profiles?
dialer pool-member
dialer-group
ip address
dialer string
Correct Answer :
A. dialer pool-member
Related Questions
Which type of traffic is sent to a group of devices?
Multicast
Unicast
Broadcast
Groupcast
The address of a Frame Relay VC is called a ___________.
Data link layer connection identifier
Data layer connection index
Data link connection index
Data link connection identifier
When using debug with PAP, which of the following message types might you see?
AUTH-ACK
SUCCESS
CHALLENGE
None of these
You are given a Class B network with a subnet mask of 255.255.255.192. How many host
addresses are there on each subnet?
30
62
126
254
Ethernet ___________ has/have both a physical and logical bus topology.
10BaseT
10Base2 and 10Base5
10BaseT and 10Base2
10BaseT, 10Base2, and 10Base5
Which frame field is different between ISO HDLC and Cisco's HDLC?
Address
Control
Flag
Proprietary
___________ defines LAPD, which is responsible for the data-link layer connection between the router and the ISDN switch.
Q.931
Q.921
I.921
I.931
Which of the following reasons might you need to use address translation?
You have to use public addressing because your ISP didn't assign you enough private addresses.
You are using private addresses but have changed ISPs, and your new ISP won't support these private addresses.
You want to assign the same IP address to multiple machines so that users on the Internet see this offered service as a single logical computer.
You are merging two companies that use different address spaces.
_________ allows you to create this summarization: 10.0.0.0/7.
Subnetting
CDR
Supernetting
VLSM
Which router command would you use to test only layer-3 connectivity?
telnet
show cdp traffic
show interfaces
traceroute
EIGRP generates hellos every _________ seconds on LAN segments.
5
10
15
30
Which IGRP command allows unequal-cost load balancing?
variance
load
balance
network
Extended traceroute works from which mode?
User EXEC
Privilege EXEC
Configuration
User and Privilege EXEC
EIGRP will route for ___________.
IP
IP and IPX
IP and AppleTalk
IP, IPX, and AppleTalk
RIP has a maximum hop count of ____________ hops.
10
15
16
100
EIGRP uses the _________ algorithm to update its routing table.
Bellman-Ford
Dijkstra
DUAL
Integrated
RIP supports load balancing for up to __________ ___________ paths.
Six, unequal-cost
Four, unequal-cost
Four, equal-cost
Six, equal-cost
_________ is/are a routed protocol.
RIP
OSPF
Both RIP and OSPF
Neither RIP or OSPF
RIP has a hold-down period of ____________ seconds.
60
120
180
280
Which router command specifies the ISDN switch the router is connected to?
isdn switch-type
isdn connection-type
isdn spid1
interface serial0:15
The _________ command takes you from User EXEC mode to Privilege EXEC mode
DISABLE
ENABLE
When configuring your terminal emulation software for a console connection, set the flow control to __________.
Hardware
Software
None
You are given a class C network, 192.168.1.0/24. You need one network with 120 hosts and three networks with 60 hosts. What subnet mask values would you use?
255.255.255.128 and 255.255.255.192
255.255.255.128
255.255.255.192
None of these
The TCP/IP protocol stack has ________ layers.
4
5
6
7
Which of the following situations are best for DDR connections?
Primary WAN connection
A lot of constant traffic
Long phone calls
Backup connection
You have ISL trunks in your network and five VLANs configured. How many instances of STP are running?
1
5
10
15
Which is not one of the three main functions of a layer-2 device?
Learning
Forwarding
Listening
Removing loops
You have this binary value: 11000001. This equates to _____ in decimal.
183
193
173
203
OSPF uses __________ as a metric.
Bandwidth
Delay
Cost
Hop count
Which would you use to move your cursor back one word?
ESC-B
esc-p
ctrl-b
ctrl-p