Related Questions
What is the correct answer?
4
Laser is a device to produce
D. A beam of coherent light
What is the correct answer?
4
During decarburising of a plain carbon steel, the thickness of ferrite layer growth is proportional to
What is the correct answer?
4
A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C.
What is the correct answer?
4
Which of the following heat treatment processes is usually applied to castings?
What is the correct answer?
4
Desalination of water
C. Means distillation of water
What is the correct answer?
4
The trace metal present in insulin is
What is the correct answer?
4
The value of for air & most common gases can be safely assumed to be
What is the correct answer?
4
Factor of safety in machine design is defined as the ratio of ultimate stress to __________ stress.
What is the correct answer?
4
Laser welding is widely employed in the __________ industries.
What is the correct answer?
4
Age hardening is connected with
What is the correct answer?
4
Pressure exerted by a liquid depends upon its
What is the correct answer?
4
LVDT used for displacement measurement is a/an __________ transducer.
What is the correct answer?
4
at 1173E; at equilibrium, what will be the number of moles of CO gas required to reduce one mole of at 1173 K?
What is the correct answer?
4
Fibre reinforced plastic (FRP) are
A. Made of glass fibre and thermoplastic resins
C. Made of thermosetting resin and glass fibre
What is the correct answer?
4
CANDU type nuclear reactor using natural uranium as fuel is the extensively used nuclear reactor because of the fact that the
A. Specific fuel consumption is very low due to the use of heavy water
B. Fuel cost is much lower than that used in pressurised water or boiling water reactor
C. Heavy water is used both as coolant as well as moderator
What is the correct answer?
4
In a furnace with heating element temperature at 1700°C, the dominant mechanism of heat transfer will be
What is the correct answer?
4
Biological shield in a nuclear reactor is generally provided to protect against the
What is the correct answer?
4
Pick out the wrong statement.
A. Seam welding, projection welding & spot welding are the classification of electrical resistance welding
B. Electrode tip in spot welding is of copper and the tip diameter should be equal to t (where, t = plate thickness to be welded)
C. In spot welding, two pieces to be joined are overlapped and placed between two electrodes
D. Mild steel sheet cannot be spot welded
What is the correct answer?
4
In an amorphous material, atoms defy any definite atomic structure and exist in random pattern just like in liquid. Which of the following is an amorphous material?
What is the correct answer?
4
Gantt charts are used for streamlining the
What is the correct answer?
4
Which of the following approaches the ideal gas behaviour most closely?
What is the correct answer?
4
Thermal conductivity of a material does not depend upon its
What is the correct answer?
4
The thickness of oxide film is y at time t. If are the temperature dependent constants, the parabolic law of oxidation is given by
What is the correct answer?
4
Brazing filler metal used for joining steel plates
A. Melts below the melting points of base metals
C. Is copper phosphorous alloy
What is the correct answer?
4
Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen.
What is the correct answer?
4
Screws are specified by their __________ diameters.
What is the correct answer?
4
Brittleness induced due to the presence of sulphur in steel can be reduced by adding
What is the correct answer?
4
Calorific value of __________ are almost same.
A. Lignite & anthracite coal
D. Coal gas & natural gas
What is the correct answer?
4
As the fluid flow rate increases, the float of the Rotameter
B. Rotates at higher speed
C. Rotates at lower speed
D. Drops down in the tube
What is the correct answer?
4
The cathode in an electrochemical cell always carries
D. Positive or negative charge depending upon the nature of the cell