Home
Current Affairs January 2024

What is the correct answer?

4

Which of the following formula is used in designing a connecting rod?

A. Euler's formula

B. Rankine's formula

C. Johnson's straight line formula

D. Johnson's parabolic formula

Correct Answer :

B. Rankine's formula


Related Questions

What is the correct answer?

4

A tap bolt

A. Has a head on one end and a nut fitted to the other

B. Has head at one end and other end fits into a tapped hole in the other part to be joined

C. Has both the ends threaded

D. Has pointed threads

What is the correct answer?

4

The cross-section of the arm of a bell crank lever is

A. Rectangular

B. Elliptical

C. I-section

D. Any one of these

What is the correct answer?

4

A double fillet welded joint with parallel fillet weld of length l and leg s is subjected to a tensile force P. Assuming uniform stress distribution, the shear stress in the weld is given by

A. √2P/s.l

B. P/2.s.l

C. P/√2.s.l

D. 2P/s.l

What is the correct answer?

4

The difference between the tooth space and the tooth thickness as measured on the pitch circle, is called

A. Working depth

B. Clearance

C. Backlash

D. Face width

What is the correct answer?

4

The deflection of a cantilever beam under load W is 8. If its width is halved, then the deflection under load W will be

A. 2/8

B. 8/2

C. 4/8

D. 8/4

What is the correct answer?

4

The pitch diameter is the __________ diameter of an external or internal screw thread.

A. Effective

B. Smallest

C. Largest

D. None of these

What is the correct answer?

4

Two shafts will have equal strength, if

A. Diameter of both the shafts is same

B. Angle of twist of both the shafts is same

C. Material of both the shafts is same

D. Twisting moment of both the shafts is same

What is the correct answer?

4

The included angle for the V-belt is usually

A. 10°-20°

B. 30°-40°

C. 40°-60°

D. 60°-80°

What is the correct answer?

4

The modulus of elasticity for mild steel is approximately equal to

A. 80 kN/mm²

B. 100 kN/mm²

C. 110 kN/mm²

D. 210 kN/mm²

What is the correct answer?

4

Lewis form factor for 14 ½° composite and full depth involute system is (where T = Number of teeth)

A. 0.124 - (0.684/T)

B. 0.154 - (0.912/T)

C. 0.175 - (0.841/T)

D. None of these

What is the correct answer?

4

In hydrostatic bearings

A. The Oil film pressure is generated only by the rotation of the journal

B. The oil film is maintained by supplying oil under pressure

C. Do not require external supply of lubricant

D. Grease is used for lubrication

What is the correct answer?

4

A tapered key which fits in a key-way in the hub and is flat on the shaft, is known as

A. Woodruff key

B. Feather key

C. Flat saddle key

D. Gib head key

What is the correct answer?

4

A key capable of tilting in a recess milled out in a shaft is known as

A. Woodruff key

B. Feather key

C. Flat saddle key

D. Hollow saddle key

What is the correct answer?

4

In a multiple V-belt drive, if one of the belts break, then

A. Only the broken belt is replaced

B. The entire set of belts is replaced

C. The broken belt and the belt on either side of it, is replaced

D. The broken belt need not to be replaced

What is the correct answer?

4

A circular shaft can transmit a torque of 5 kN-m. If the torque is reduced to 4 kN-m, then the maximum value of bending moment that can be applied to the shaft is

A. 1 kN-m

B. 2 kN-m

C. 3 kN-m

D. 4 kN-m

What is the correct answer?

4

The shear stress in a beam varies from zero at the outer fibres to a maximum at the________.

A. Neutral surface

B. Upper surface

C. Lower surface

D. None of these

What is the correct answer?

4

The edges of a boiler plate are bevelled to an angle of

A. 30°

B. 45°

C. 60°

D. 80°

What is the correct answer?

4

A sliding bearing in which although lubricant is present, the working surfaces __________ contact each other at least part of the time, is called boundary lubricated bearing.

A. Partially

B. Fully

C. Either A or B

D. None of these

What is the correct answer?

4

The centre to centre distance between two consecutive rivets in a row, is called

A. Margin

B. Pitch

C. Back pitch

D. Diagonal pitch

What is the correct answer?

4

A chain drive transmits __________ power as compared to belt drive.

A. More

B. Less

C. Same

D. None of these

What is the correct answer?

4

A bolt of uniform strength can be developed by

A. Keeping the core diameter of threads equal to the diameter of unthreaded portion of the bolt

B. Keeping the core diameter smaller than the diameter of the unthreaded portion

C. Keeping the nominal diameter of threads equal to the diameter of unthreaded portion of the bolt

D. None of the above

What is the correct answer?

4

In cross or regular lay ropes

A. Direction of twist of wires in strands is opposite to the direction of twist of strands

B. Direction of twist of wires and strands are same

C. Wires in two adjacent strands are twisted in opposite direction

D. Wires are not twisted

What is the correct answer?

4

Stress concentration in static loading is more serious in

A. Ductile materials

B. Brittle materials

C. Equally serious in both cases

D. Depends on other factors

What is the correct answer?

4

The velocity factor for ordinary cut gears operating at velocities upto 12.5 m/s is equal to

A. 0.75/ (0.75 + √v)

B. 3/ (3 + v)

C. 4.5/ (4.5 + v)

D. 6/ (6 + v)

What is the correct answer?

4

For a shaft diameter of 100 mm, the number of bolts in a flange coupling should be

A. 4

B. 6

C. 8

D. 10

What is the correct answer?

4

Brittle coating technique is used for

A. Determining brittleness

B. Protecting metal against corrosion

C. Protecting metal against wear and tear

D. Experimental stress analysis

What is the correct answer?

4

The material generally used for aircraft components is

A. Mild steel

B. High speed steel

C. Stainless steel

D. Aluminium

What is the correct answer?

4

The static tooth load should be __________ the dynamic load.

A. Equal to

B. Less than

C. Greater than

D. None of these

What is the correct answer?

4

The endurance limit in shear of carbon steel can be obtained by multiplying the endurance limit in flexure by a factor of

A. 0.45

B. 0.55

C. 0.65

D. 0.75

What is the correct answer?

4

At low temperatures (say 75°C) the notched bar impact value of steel

A. Increases markedly

B. Decreases markedly

C. Remain same

D. Depends on heat treatment carried out