Related Questions
What is the correct answer?
4
Between 230 and 370°C, blue brittleness is caused in mild steel because of the
A. Immobility of dislocation
C. Increase in Young's modulus
What is the correct answer?
4
Nitriding of a steel part does not increase its
What is the correct answer?
4
While the recrystallisation temperature for pure metals is 0.3 Tm, the same for alloys is equal to __________ × Tm (where, Tm Melting temperature).
What is the correct answer?
4
Two wires of the same radius & material having length in the ratio of 1 : 2 are stretched by the same force. The strain produced in the two wires will be in the ratio of
What is the correct answer?
4
Specific gravity of hot metal (pig iron) is __________ times that of the blast furnace slag.
What is the correct answer?
4
Corrosion of metals cannot be prevented by its
What is the correct answer?
4
Property responsible for the talcum powder to cling to the skin is the
What is the correct answer?
4
__________ is not a heat treatment process.
What is the correct answer?
4
__________ cannot increase the fatigue strength of a material.
What is the correct answer?
4
Fatigue resistance of a material is measured by the
B. Ultimate tensile strength
What is the correct answer?
4
Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling.
What is the correct answer?
4
The excess air required for the combustion of pulverised coal is of the order of about __________ percent.
What is the correct answer?
4
Blow off cock is provided in steam boiler to
A. Guard the boiler in case of abnormal rise in steam pressure
B. Drain out water and sludge during its repair
C. Regulate the supply of water in boiler
D. Put out the fire in the furnace when the water level in the boiler falls to unsafe limit
What is the correct answer?
4
Use of flux during soldering is done to
A. Increase fluidity of solder by lowering its melting temperature
B. Prevent oxide formation
C. Wash away surplus solder
What is the correct answer?
4
An approximately __________ process exemplifies the flow of a gas through a very long pipe of uniform cross-section.
What is the correct answer?
4
Holes for riveting purposes should be preferably made by
What is the correct answer?
4
Identify the correct statement.
A. Sphlerite is zinc oxide
B. The first law of the thermodynamics is stated as δE = δQ - δW
C. Lead can be produced in a blast furnace
D. T. ferrooxidans is a fungus that can be used for leaching chalcopyrite
What is the correct answer?
4
Blasting of tri-nitro-toluene (TNT) is done by mixing it with ammonium
What is the correct answer?
4
Nickel is a __________ material.
What is the correct answer?
4
The noble metals
A. Are exemplified by Na, K and Li
B. Do not resist corrosion very strongly
C. Are the lowermost in the electro-chemical series of metals
What is the correct answer?
4
'Amortization' in respect of financial obligation of a company means the
A. Liquidation of financial obligations on instalment basis
B. Commitment of financial obligation on priority
C. Liquidation of all the obsolete equipments of the company
D. Modernisation of the plant equipments
What is the correct answer?
4
Steel is welded using the __________ flame.
What is the correct answer?
4
A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of thermal conductivity 0.14 W/m.K and thickness __________ metre.
What is the correct answer?
4
Which of the following is an ore dressing operation?
What is the correct answer?
4
While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the
C. Better finish and surface appearance
D. High plastic deformation
What is the correct answer?
4
Consideration of the creep is the most important in case of the
B. Piston of an I. C. engine
C. Flywheel of steam engine
What is the correct answer?
4
Catalyst used in the catalytic converter employed in automobiles to convert CO into CO2 and for complete oxidation of un-burnt hydrocarbons is
What is the correct answer?
4
Liquor poisoning generally occurs due to the presence of __________ in it.
What is the correct answer?
4
A material being tested for endurance strength is subjected to the __________ load.
What is the correct answer?
4
Which of the following rays has the least wavelength?