Related Questions
What is the correct answer?
4
If the 2950's RPS is ________, the external power supply is supplying power.
What is the correct answer?
4
What would you enter to see the last few commands you entered?
What is the correct answer?
4
An OSPF's router ID is based on __________.
A. The lowest IP address on its loopback interface, if configured, or the lowest IP address onits active interfaces
B. The highest IP address on its loopback interface, if configured, or the highest IP address on its active interfaces
C. The highest IP address on its active interfaces, if configured, or the highest IP address on its loopback interfaces
D. The lowest IP address on its active interfaces, if configured, or the lowest IP address on its loopback interfaces
What is the correct answer?
4
__________ allows you to distribute connection requests destined to a single IP address to multiple machines.
What is the correct answer?
4
RIP generates routing updates every _________ seconds.
What is the correct answer?
4
Which type of traffic is not flooded?
What is the correct answer?
4
What command creates a DHCP address pool on a router?
What is the correct answer?
4
If the port status LED on a 2950 is ________, there is a physical layer connection problem.
A. Flashing green and amber
What is the correct answer?
4
You are given a Class C network with 25 bits of networking. How many subnets do you have?
What is the correct answer?
4
Which router-on-a-stick command defines the VLAN for the interface?
What is the correct answer?
4
You execute the line console 0 command from Configuration mode. What will the router's prompt be?
C. Router(config-interface)#
What is the correct answer?
4
A ___________ is basically all of the components, hardware and software, involved
in connecting computers across small and large distances.
What is the correct answer?
4
Which of the following is not an advantage of route summarization?
A. It requires less memory and processing.
B. It supports smaller routing update sizes.
C. It contains network problems.
D. It supports discontiguous subnets.
What is the correct answer?
4
Which frame field is different between ISO HDLC and Cisco's HDLC?
What is the correct answer?
4
Which type of routing protocol uses the Shortest Path First algorithm?
What is the correct answer?
4
RIP has a maximum hop count of ____________ hops.
What is the correct answer?
4
EIGRP will route for ___________.
D. IP, IPX, and AppleTalk
What is the correct answer?
4
Which of the following is true concerning RIPv2?
A. It uses triggered updates.
D. It doesn't support route summarization
What is the correct answer?
4
Which of the following is true concerning bridges?
A. They switch frames in hardware.
B. They support half- and full-duplexing.
C. They support one collision domain for the entire bridge.
D. They do only store-and-forward switching.
What is the correct answer?
4
Your router is running RIP and OSPF and both routing protocols are learning 192.168.1.0/24. Which routing protocol will your router use for this route?
What is the correct answer?
4
A _________ is used to connect networking devices that are in a very close geographic area, such as a floor of a building, a building itself, or a campus environment.
What is the correct answer?
4
172.16.240.256 is a class __________ address.
What is the correct answer?
4
Which control sequence moves the cursor to the end of the line?
What is the correct answer?
4
When backing up your IOS image from flash, which of the following will the copy flash tftp command prompt you for? (Choose all correct answers.)
A. TFTP server IP address
What is the correct answer?
4
Which of the following is false concerning CHAP?
A. It sends an encrypted password.
C. It is more secure than PAP.
D. It uses a three-way handshake.
What is the correct answer?
4
The ___________ converts an ISDN four-wire connection to a two-wire connection.
What is the correct answer?
4
Which of the following are classless protocols?
What is the correct answer?
4
With a crossover cable, which pins are crossed over?
What is the correct answer?
4
Which prompt indicates that you are at User EXEC mode?
What is the correct answer?
4
With _________ switching, the switch reads the destination MAC address of the frame and
immediately starts forwarding the frame.