Related Questions
What is the correct answer?
4
Which of the following is the most suitable material of construction for the condenser tubes, where the cooling medium is brine (salty water)?
What is the correct answer?
4
In case of a, centrifugal pump, the ratio h1/h2 is termed as the __________ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller).
What is the correct answer?
4
Dryness fraction of dry steam is
What is the correct answer?
4
A fluid is termed as the Newtonian fluid, when the shear stress is __________ the velocity gradient.
B. Inversely proportional to
C. Directly proportional to
What is the correct answer?
4
In chemical dehumidification of air
A. Both specific humidity & dry bulb temperature increases
B. Both specific humidity & dry bulb temperature decreases
C. Specific humidity decreases & dry bulb temperature increases
D. Specific humidity increases & dry bulb temperature decreases
What is the correct answer?
4
Multistage compression of air as compared to single stage compression offers the advantage of
A. Power saving per unit weight of air delivered
B. Moisture elimination in the inter-stage cooler
C. Increased volumetric efficiency
What is the correct answer?
4
Fibrous fracture is normally encountered in the __________ materials.
What is the correct answer?
4
Exposure to __________ accelerates the degradation of plastics.
B. High atmospheric temperature
C. High ambient temperature
What is the correct answer?
4
Which of the following fastening devices has its both ends threaded?
What is the correct answer?
4
Though tin occurs lower than iron in the electrochemical series, yet it is coated on steel for corrosion protection, because of its
C. Resistance to vegetable acids as the tin plate are commercially used in 'canning' industry
What is the correct answer?
4
Stainless steel is welded with difficulty because of
A. Its high melting temperature
D. Chromium carbide formation
What is the correct answer?
4
Highest cutting speed is achieved by the __________ tool material.
What is the correct answer?
4
The normal stress is the same in all directions at a point in a fluid, only when the fluid
A. Is at rest & has zero viscosity
C. Fluid layer has no motion relative to an adjacent layer of fluid
D. is incompressible & frictionless
What is the correct answer?
4
Which of the following materials has the poorest electrical conductivity?
What is the correct answer?
4
__________ is the hardest material out of the following.
What is the correct answer?
4
Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling.
What is the correct answer?
4
Which of the following is not an ore of copper?
What is the correct answer?
4
The most suitable material of construction for a sewer to carry sewage under high pressure is
What is the correct answer?
4
The heat of neutralisation remains constant, when there is a reaction between dilute solutions of strong
What is the correct answer?
4
Plants produce carbohydrates from the CO2 present in the atmosphere by
B. Photochemical reaction
What is the correct answer?
4
Steels with high carbon equivalent have poor Weldability, because in these steels during welding
A. Carbon and other alloying elements get oxidised from the weld pool
B. Excessive ferrite forms in the heat affected zone leading to poor toughness of the weld
C. Martensite forms in the heat affected zone leading to poor toughness/ductility of the weld
D. Segregation of carbon and other element occurs in the weld pool leading to poor properties of the weld
What is the correct answer?
4
Flue gases pass through the following boiler accessories in a high pressure natural circulation boiler.
A. Induced draft fan
B. Economiser
C. Air preheater
D. Steam superheater Which of the following gives the correct sequence of flow of the flue gases through the above mentioned boiler accessories?
What is the correct answer?
4
Which of the following metals is not subjected to electrolytic refining/purification?
What is the correct answer?
4
Which of the following materials has the maximum shrinkage allowance?
What is the correct answer?
4
Eutectoid composition of carbon steel at room temperature is
What is the correct answer?
4
The elastic strain in copper is due to the
A. Motion of dislocations
B. Stretching of atomic bonds
C. Breakage of atomic bonds
What is the correct answer?
4
What is the value of included angle of a triangular notch for maximum discharge?
What is the correct answer?
4
Frother is added in the froth floatation cell used in ore beneficiation to stabilise the air bubbles (i.e., froth), which will hold the ore particles, but it does not affect the floatability of minerals. Which of the following is not used as a frother?
What is the correct answer?
4
Air standard Otto cycle is more efficient than the diesel cycle for the same
A. Heat addition & compression ratio
B. Heat addition & pressure
C. Compression ratio & pressure
D. Cylinder dimension & rpm
What is the correct answer?
4
Minimum safe distance between two liquid fuel storage tanks is equal to (where, H = height of the tank)