Related Questions
What is the correct answer?
4
Which of the, following is not associated with the functioning of a petrol engine?
A. Compression ignition system
What is the correct answer?
4
Titanium is produced by __________ of Ti Cl4.
A. Electrolytic reduction
What is the correct answer?
4
Tesla metre per ampere (T. m/A) is the unit for the measurement of
A. Magnetic susceptibility
C. Permeability of free space
What is the correct answer?
4
Yield strength of a material is determined by the __________ test.
What is the correct answer?
4
The following type of bonding is strongly directional in solids.
What is the correct answer?
4
Cupola produces __________ iron.
What is the correct answer?
4
Hot working of lead is carried out at
What is the correct answer?
4
The ratio of the shear stress to the principal stress on a principal plane is
What is the correct answer?
4
The excess air required for the combustion of pulverised coal is of the order of about __________ percent.
What is the correct answer?
4
Which of the following mainly decides the current to be employed is arc welding?
C. Voltage across the arc
What is the correct answer?
4
During sensible cooling of air, its wet bulb temperature
A. Decreases but dew point remains constant
B. Increases but dew point remains constant
C. Increases & the dew point decreases
D. Decreases & the dew point increases
What is the correct answer?
4
__________ is the process used for setting up compressive stresses in the surface of a metal to improve its fatigue strength.
What is the correct answer?
4
Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2 .k), when the insulation thickness is __________ mm.
What is the correct answer?
4
Methyl orange indicator turns
A. Orange yellow in alkaline medium
B. Orange yellow in acidic medium
C. Colourless in acidic medium
D. Colourless in basic medium
What is the correct answer?
4
Diameter of the rivet to be provided on a 20 mm. thick boiler plate will be __________ mm.
What is the correct answer?
4
Triple point of water is
What is the correct answer?
4
In case of simple harmonic motion, displacement is proportional to the
What is the correct answer?
4
Which of the following parameters is not responsible for the heat loss from a hot steam carrying bare pipe surface located in a room without fans?
A. Emissivity of pipe surface
B. Diameter & length of the pipe
C. Temperature of hot pipe surface & that of air in the room
What is the correct answer?
4
The most important consideration in value engineering is the
What is the correct answer?
4
Out of the following the refractive index is the highest for
What is the correct answer?
4
Which of the following is prone to cup and cone fracture?
C. Round specimen of ductile metal
D. Flat tensile specimen of ductile metal
What is the correct answer?
4
Dielectric
A. Is an electrical insulating material
B. Of low resistivity is preferred
C. Should have high thermal conductivity
D. Need not defy the corrosive action of chemicals
What is the correct answer?
4
The best guide to judge the general quality of water is the measurement of its
B. Electrical conductivity
D. Dissolved oxygen content
What is the correct answer?
4
Addition of silicon to cast iron
A. Promotes graphite module formation
B. Improves its ductility
C. Does not promote graphite flakes formation
D. Increases the fluidity of molten metal
What is the correct answer?
4
__________ temperature remains constant during adiabatic saturation process of unsaturated air.
What is the correct answer?
4
__________ is not a heat treatment process.
What is the correct answer?
4
Titanium is added to molten aluminium alloys before casting for the purpose of
B. Increasing corrosion resistance
What is the correct answer?
4
The temperature at which the magnetic property of iron disappears (i.e., it becomes non-magnetic) and its electrical conductivity & specific heat also changes, is called the 'Curie point', which is __________ °C.
What is the correct answer?
4
__________ the exhaust gas is an indication of the incomplete combustion of fuel.
What is the correct answer?
4
The heat treatment to which the steel wire containing > 0.25% carbon is subjected to is