Related Questions
What is the correct answer?
4
Steel produced from phosphatic iron is __________ in nature.
What is the correct answer?
4
Brittleness induced due to the presence of sulphur in steel can be reduced by adding
What is the correct answer?
4
The heat released by cooling one mole of copper from 400 K to room temperature (300 K) is (assume : Cp of copper is 23 J K-1mole-1)
What is the correct answer?
4
Which of the following is not the function of a volute casing provided in a centrifugal pump?
A. To reduce the head loss in discharge
B. To increase the pump efficiency
C. To collect liquid from the periphery of the impeller and to transmit it to the delivery pipe at constant velocity
D. To increase the pump discharge rate
What is the correct answer?
4
The co-ordination number in simple cubic structure is
What is the correct answer?
4
In __________ process, there is an increase in entropy with no degradation of energy.
B. Isochoric heat addition
D. Isobaric heat addition
What is the correct answer?
4
Gage pressure within a spherical droplet of a fluid is 'p'. What will be gage pressure within a bubble of the same size & of the same fluid?
What is the correct answer?
4
Biological shield in a nuclear reactor is generally provided to protect against the
What is the correct answer?
4
Out of the following, the __________ pipe has the least corrosion resistance.
What is the correct answer?
4
__________ is not used as a material of construction in thermocouples.
What is the correct answer?
4
'GASOHOL' widely used in Brazil as a motor fuel is a mixture of alcohol and
C. Light hydrocarbon gases (e.g. butane or propane)
What is the correct answer?
4
Carbon is present in the form of __________ in grey cast iron.
B. Nodular aggregates of graphite
What is the correct answer?
4
Broaching tools are usually made of
What is the correct answer?
4
The difference in one unit of Rockwell hardness number corresponds to a difference in the depth of indentation of __________ mm.
What is the correct answer?
4
Electrochemical corrosion can occur, only if __________ is present in contact with metal.
What is the correct answer?
4
The most prominent single cause of corrosion in boiler-tubes, drums, economisers and steam superheaters in a thermal power plant boiler is the
A. Water alkalinity & leakage
B. Hydrazine addition during feed water treatment
C. Release of non-condensable gas from water in the boiler
What is the correct answer?
4
Reduction in the grain size reduces the __________ of the material.
What is the correct answer?
4
In fluid flow, and heat and mass transfer, one encounters (i) kinematic velocity (μ), (ii) molecular diffusivity (θ) and thermal diffusivity (α). The units of these quantities are.
A. μ , α and θ all have units of m/s
B. μ , α and θ all have units of m2/s
C. α and θ have units of m2/s, while μ has unit of m/s
D. α and θ have units of m/s, while μ has unit of m2/s
What is the correct answer?
4
The most suitable material for die casting is
What is the correct answer?
4
The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the
What is the correct answer?
4
The burnout heat flux in the nucleate boiling regime is not a function of the
C. Temperature difference
What is the correct answer?
4
The condition of diffraction from a crystal is given by
What is the correct answer?
4
Which of the following is the most wear resistant grade of carbide used for the cutting tools?
What is the correct answer?
4
Saturated steam at a pressure of 25 kg/cm2 is throttled to attain 5 kg/cm2. Then the outcoming steam will be
What is the correct answer?
4
Which of the following is a commonly used manometric liquid for low pressure range?
What is the correct answer?
4
at 1173E; at equilibrium, what will be the number of moles of CO gas required to reduce one mole of at 1173 K?
What is the correct answer?
4
Water flow in the river during flood can be categorised as the __________ flow.
What is the correct answer?
4
Which of the following materials does not form adherent oxide film on surface?
What is the correct answer?
4
Work required for compression of a gas contained in a cylinder is 7000 kJ. During compression, heat interaction of 3000 kJ causes the surroundings to be heated. Internal energy change of the gas during the compression is __________ kJ.
What is the correct answer?
4
__________ of test specimens is not involved in any hardness testing method.