Related Questions
What is the correct answer?
4
Case hardening of a material is
A. Followed by tempering or carburising
B. Preceded by its tempering
C. Done to get a soft ductile interior with a very hard surface
D. Carried out to get extreme hardness in its core
What is the correct answer?
4
Silicon crystal can be converted to p-type semiconductor by doping with
What is the correct answer?
4
Main constituent of bone ash is
What is the correct answer?
4
Normalising does not __________ of a metal.
A. Improve machinability & tensile strength
B. Remove internal stresses
D. Remove strains caused by cold working
What is the correct answer?
4
Tin based white metals are used, where bearings are subjected to
What is the correct answer?
4
Fibre reinforced plastic (FRP) are
A. Made of glass fibre and thermoplastic resins
C. Made of thermosetting resin and glass fibre
What is the correct answer?
4
A material being tested for endurance strength is subjected to the __________ load.
What is the correct answer?
4
__________ pipe is the most suitable for carrying sanitary drainage.
B. Reinforced cement concrete
What is the correct answer?
4
Colour comparator is used to measure the
What is the correct answer?
4
If a nuclear reactor produces more fissile nuclear fuel than it consumes, then it is called a __________ reactor.
What is the correct answer?
4
When the wet steam is throttled but still remains wet at the exit of the throttle valve, then its temperature & dryness fraction respectively
What is the correct answer?
4
For a first order chemical reaction, the concentration of the reactant decreases __________ with time.
What is the correct answer?
4
The concentration of (H+) ions is 4 x 10-5 in a solution. Then pH of the solution will be (Given log 4 = 0.6)
What is the correct answer?
4
Presence of nickel & chromium in steel does not raise its
What is the correct answer?
4
The swift cup test evaluates the following property of a sheet metal.
What is the correct answer?
4
A polymer is termed as an 'elastomer', if its percentage elongation is more than 100%. An elastomer is termed as 'rubber' if its percentage elongation is more than __________ percent.
What is the correct answer?
4
Work done by a/an __________ process is determined by ∫p. dv
What is the correct answer?
4
Strain hardening effect in a metal subjected to cold working is due to the __________ mechanism.
What is the correct answer?
4
The cooling rate required to freeze 1 ton of water at 0°C into ice at 0°C in 24 hours is __________ BTU/hr.
What is the correct answer?
4
Inertial forces are obtained, when the elastic forces are multiplied by __________ number.
What is the correct answer?
4
Temperature profile along the length of a gasgas counter flow heat exchanger is correctly represented by
What is the correct answer?
4
Metallic surveying tapes are made of __________ which has a low co-efficient of expansion & enough strength.
What is the correct answer?
4
Thermal efficiency of an internal combustion engine is around __________ percent.
What is the correct answer?
4
Cemented carbide tools are not suitable for cutting
What is the correct answer?
4
__________ joint is mostly used for joining pipes carrying water at low pressure.
What is the correct answer?
4
Maximum hardenability of steel depends upon its
D. Alloying elements content
What is the correct answer?
4
The lightest non-inflammable gas is
What is the correct answer?
4
Water hammer is caused in steam carrying pipelines, because of
A. Partial condensation of steam
B. Vibration of the pipeline
C. High degree of superheat of steam
D. Its exposure to torrential rain
What is the correct answer?
4
Dislocation cross-slip is difficult in those materials, which have
A. Large number of slip systems
B. High work hardening rate
D. Low stacking fault energy
What is the correct answer?
4
Unbreakable crockeries are made from __________ polymers.