Which of the following statement is correct?
The cold rolled shafting is stronger than hot rolled shafting
The hot rolled shafting is stronger than cold rolled shafting
The cold rolled and hot rolled shaftings are equally strong
The shafts are not made by rolling process
Correct Answer :
A. The cold rolled shafting is stronger than hot rolled shafting
Related Questions
When a bolt is subjected to shock loading, the resilience of the bolt should be considered in order to prevent breakage at the
Thread
Middle
Shank
Head
Basic shaft is one
Whose upper deviation is zero
Whose lower deviation is zero
Whose lower as well as upper deviations are zero
Does not exist
The included angle between the sides of V-belt is
40°
45°
38°
60°
The relation between the pitch of the chain (p) and pitch circle diameter of the sprocket (D) is given by (where T = Number of teeth on the sprocket)
p = D sin (90°/T)
p = D sin (120°/T)
p = D sin (180°/T)
p = D sin (360°/T)
Auto frettage is the method of
Joining thick cylinders
Calculating stresses in thick cylinders
Pre-stressing thick cylinders
Increasing the life of thick cylinders
In designing a key, it is assumed that the distribution of forces along the length of key
Varies linearly
Is uniform throughout
Varies exponentially, being more at the torque-input end
Varies exponentially, being less at the torque-input end
In worm, gears, pitch lead angle is
Half the angle between two inclined faces in axial plane
The angle between the tangent to the pitch helix and the plane of rotation
The angle between the tangent to the pitch helix and an element of the cylinder
None of the above
The efficiency of a square threaded screw is maximum if the helix angle is equal to (Where φ = Angle of friction)
90° - φ
45° - φ
45° - φ/2
45° + φ/2
The contact ratio is the ratio of
Length of arc of recess to the circular pitch
Length of path of contact to the circular pitch
Length of arc of contact to the circular pitch
Length of arc of approach to the circular pitch
In a marine flange coupling, the pitch circle diameter of bolts is taken as
1.2 d
1.6 d
2d
2.5 d
Antifriction bearings are
Sleeve bearings
Hydrodynamic bearings
Thin lubricated bearings
None of the above
In unilateral system of tolerance, the tolerance is allowed on
Both sides of the actual size
One side of the actual size
One side of the nominal size
Both sides of the nominal size
For a shoe brake, the equivalent coefficient of friction is equal to (where μ = Actual coefficient of friction, and θ = Semi-block angle)
2μ sinθ/(θ + sinθ)
μ sinθ/(2θ + sin 2θ)
4μ sinθ/(θ + sinθ)
4μ sinθ/(2θ + sin 2θ)
The temperature required for full annealing in hypereutectoid steel is
50°C above upper critical temperature
50°C below upper critical temperature
50°C above lower critical temperature
50°C below lower critical temperature
For a square key made of mild steel, the shear and crushing strength are related as
Shear strength is equal to crushing strength
Shear strength is greater than crushing strength
Shear strength is less than crushing strength
None of the above
A leaf spring in automobiles is used
To apply forces
To measure forces
To absorb shocks
To store strain energy
In order to determine the stresses in a thin cylinder due to an internal pressure, it is assumed that
The effect of curvature of the cylinder wall is neglected
The tensile stresses are uniformly distributed over the section of the walls
The effect of the restraining action of the heads at the end of the pressure vessel is neglected
All of the above
The ratio of driving tensions in V-belt drives is __________ flat belt drives.
Equal to
sinα times more than
sinα times less than
cosecα times more than
In thrust bearings, the load acts
Along the axis of rotation
Parallel to the axis of rotation
Perpendicular to the axis of rotation
In any direction
A bolt of uniform strength can be developed by
Keeping the core diameter of threads equal to the diameter of unthreaded portion of the bolt
Keeping the core diameter smaller than the diameter of the unthreaded portion
Keeping the nominal diameter of threads equal to the diameter of unthreaded portion of the bolt
None of the above
Which of the following formula is used in designing a connecting rod?
Euler's formula
Rankine's formula
Johnson's straight line formula
Johnson's parabolic formula
For maximum power, the velocity of the belt will be
√(T/m)
√(T/2m)
√(T/3m)
None of these
For high speed engines, the cam follower should move with
Uniform velocity
Simple harmonic motion
Uniform acceleration and retardation
Cycloidal motion
Which one of the following is a positive drive?
V-belt drive
Rope drive
Crossed flat belt drive
Chain drive
In order to permit the thermal expansion/contraction of tubing, it should be
Crimped
Honed
Flared
Bent
Slenderness ratio is the ratio of
Effective length of column to least radius of gyration of the column
Width of column to depth of column
Maximum size of column to minimum size of column
Effective length of column to width of column
Two shafts A and B under pure torsion are of identical length and identical weight and are made of the same material. The shaft A is solid and the shaft B is hollow. We can say that
Shaft B is better than shaft A
Shaft A is better than shaft B
Both the shafts are equally good
None of these
Rankine's theory of failure is applicable for following type of materials
Brittle
Ductile
Elastic
Plastic
Tearing resistance required to tear off the plate per pitch length is (where p = Pitch of rivets, d = Dia. of rivet hole, and σt = Permissible tensile stress for plate material)
p.d.σt
p.t.σt
(p - d) σt
(p - d) t.σt
In a belt drive, if the pulley diameter is doubled keeping the tension and belt width constant, then it will be necessary to
Increase the key length
Increase the key depth
Increase the key width
Decrease the key length