Which of the following statement is wrong?
The pitch of rivets is obtained by equating the tearing resistance of the plate to the shearing resistance of the rivets
The pitch of rivets should not be less than 2d, where d is the diameter of rivet hole
The maximum value of the pitch of rivets for a longitudinal joint of a boiler, as per I.B.R., is given by Pmax = C.t + 41.28 mm
According to I.B.R., the thickness of butt strap shall not be less than 5 mm
Correct Answer :
D. According to I.B.R., the thickness of butt strap shall not be less than 5 mm
Related Questions
For a bevel gear having the pitch angle θ, the ratio of formative number of teeth (TE) to actual number of teeth (T) is
1/sinθ
1/cosθ
1/tanθ
sinθ cosθ
In second type of levers,
Load is in between the fulcrum and effort
Effort is in between the fulcrum and load
Fulcrum is in between the load and effort
None of these
Which of the following statement is correct?
A parallel sunk key is a taperless key
A parallel sunk key may be rectangular or square in cross-section
A flat saddle key is a taper key which fits in a key way of the hub and is flat on the shaft
All of the above
Which of the following is not correct procedure to increase the fatigue limit?
Cold working
Shot peening
Surface decarburisation
Under stressing
The cracks in helical springs used in railway carriages usually start on the inner side of the coil because of the fact that
It is subjected to a higher cyclic loading than the outer side
It is subjected to a higher stress than the outer side
It is more stretched than the outer side during the manufacturing process
It has a lower curvature than the outer side
Rivets are generally specified by
Thickness of plates to be riveted
Length of rivet
Diameter of head
Nominal diameter
The material generally used for aircraft components is
Mild steel
High speed steel
Stainless steel
Aluminium
A thin spherical shell of internal diameter d is subjected to an internal pressure p. If V is the storage capacity of shell, then its diameter will be
(6V/ π)1/2
(6V/ π)1/3
(6V/ π)2
(6V/ π)3
When bevel gears having equal teeth and equal pitch angles connect two shafts whose axes intersect at right angle, then they are known as
Angular bevel gears
Crown bevel gears
Internal bevel gears
Mitre gears
The plasticity is the property of a material which enables it to
Regain its original shape after deformation when the external forces are removed
Draw into wires by the application of a tensile force
Resist fracture due to high impact loads
Retain deformation produced under load permanently
A crankshaft is a __________ shaft.
Transmission
Machine
Machine frame
None of these
If two springs are in parallel then their overall stiffness will be
Half
Same
Double
None of the above
Multiple threads are used to secure
Low efficiency
High efficiency
High load lifting capacity
High mechanical advantage
According to Indian standard specifications, 100 H6/g5 means that the
Basic size is 100 mm
Actual size is 100 mm
Difference between the actual size and basic size is 100 mm
None of the above
In worm, gears, pitch lead angle is
Half the angle between two inclined faces in axial plane
The angle between the tangent to the pitch helix and the plane of rotation
The angle between the tangent to the pitch helix and an element of the cylinder
None of the above
A bolt of M 24 × 2 means that
The pitch of the thread is 24 mm and depth is 2 mm
Cross-sectional area of the threads is 24 mm²
The nominal diameter of bolt is 24 mm and pitch is 2 mm
The effective diameter of bolt is 24 mm and there are 2 threads per cm
In case of thick cylinders, the tangential stress across the thickness of cylinder is
Maximum at the outer surface and minimum at the inner surface
Maximum at the inner surface and minimum at the outer surface
Maximum at the inner surface and zero at the outer surface
Maximum at the outer surface and zero at the inner surface
While designing a screw in a screw jack against buckling failure, the end conditions for the screw are taken as
Both the ends fixed
Both the ends hinged
One end fixed and the other end hinged
One end fixed and the other end free
The connecting rod bolts are tightened up with initial tension greater than the external load so that
Joint may not open up
Bolts are weakest elements
The resultant load on the bolt would not be affected by the external cyclic load
Bolts will not loosen during service
Slenderness ratio is the ratio of
Effective length of column to least radius of gyration of the column
Width of column to depth of column
Maximum size of column to minimum size of column
Effective length of column to width of column
The value of stress concentration factor depends upon
Material and geometry of the part
Geometry of the part
Material of the part
None of these
In designing a key, it is assumed that the distribution of forces along the length of key
Varies linearly
Is uniform throughout
Varies exponentially, being more at the torque-input end
Varies exponentially, being less at the torque-input end
When the bearing is subjected to large fluctuations of load and heavy impacts, the bearing characteristic number should be _________ the bearing modulus.
10 times
5 times
15 times
20 times
When the connected members are very yielding (soft gasket) as compared to the bolt, then the resultant load on the bolt will be equal to the
Initial tension
External load applied
Sum of the initial tension and external load applied
Initial tension or external load, whichever is greater
If a material fails below its yield point, failure would be due to
Straining
Fatigue
Creep
Sudden loading
A compound cylinder with inner radius 50 mm and outer radius 70 mm is made by shrinking one cylinder on to the other cylinder, the junction radius is 60 mm and the junction pressure is 1.1 N/mm². The maximum hoop stress developed in the inner cylinder is
3.6 N/mm² compression
3.6 N/mm² tension
7.2 N/mm² compression
7.2 N/mm² tension
In designing a connecting rod, it is considered like __________ for buckling about Y-axis.
Both ends hinged
Both ends fixed
One end fixed and the other end hinged
One end fixed and the other end free
Which of the following is a permanent fastening?
Bolts
Keys
Cotters
Rivets
In a steam engine, the piston rod is usually connected to the crosshead by means of a
Knuckle joint
Cotter joint
Oldham coupling
Universal joint
Screws used for power transmission should have
Very fine threads
High efficiency
Low efficiency
Strong teeth