Related Questions
What is the correct answer?
4
Spherical shape of mercury droplets is due to its
What is the correct answer?
4
Out of the following, the joint produced by __________ has the lowest strength.
What is the correct answer?
4
Lap joints are preferred over butt joints in soldering/brazing, because these joints are
A. Weaker in tension but stronger in shear
B. Weaker in shear but stronger in tension
C. Stronger in both shear and tension
D. The lap joints are easily made
What is the correct answer?
4
__________ is used as a material of construction for the blade of power saw.
What is the correct answer?
4
Wrought iron is never shaped by
What is the correct answer?
4
What is the percentage of chromium in 18-4-1 high speed steel?
What is the correct answer?
4
The life of a ball bearing is inversely proportional to
What is the correct answer?
4
Steels with high carbon equivalent have poor Weldability, because in these steels during welding
A. Carbon and other alloying elements get oxidised from the weld pool
B. Excessive ferrite forms in the heat affected zone leading to poor toughness of the weld
C. Martensite forms in the heat affected zone leading to poor toughness/ductility of the weld
D. Segregation of carbon and other element occurs in the weld pool leading to poor properties of the weld
What is the correct answer?
4
Which one of the following is incombustible?
What is the correct answer?
4
Neutrons are present in all atoms except that of
What is the correct answer?
4
The majority charge carriers in p-type silicon are
What is the correct answer?
4
The units of the rate constant for a second order reaction are
What is the correct answer?
4
Basic open hearth furnace (BOF) is not used for producing __________ steel.
What is the correct answer?
4
Silicon in steel
A. Makes it usable in almost all magnetic circuits where alternating current is used
B. Increases its electrical resistivity and decreases the hysteresis loss
C. Is present upto 5% & 4% respectively when used in transformers & motor armatures
What is the correct answer?
4
The elastic strain energy of a unit length of an edge dislocation as compared to that of a screw dislocation is
What is the correct answer?
4
Minimum temperature upto which water can be theoretically cooled down in the cooling tower by evaporative cooling is equal to the __________ temperature of air.
What is the correct answer?
4
__________ cannot increase the fatigue strength of a material.
What is the correct answer?
4
Strain hardening effect in a metal subjected to cold working is due to the __________ mechanism.
What is the correct answer?
4
In TIG welding, thoriated tungsten electrodes are used, because it
A. Has higher current carrying capacity
B. Has better electron emissivity
C. Is stronger than ordinary tungsten
What is the correct answer?
4
Inertial forces are obtained, when the elastic forces are multiplied by __________ number.
What is the correct answer?
4
Strain hardening effect in metals subjected to cold working is due to the __________ mechanism.
What is the correct answer?
4
Powder metallurgy process does not make metal powder by
D. Electrolytic deposition
What is the correct answer?
4
Hardening of steel is not possible, unless it is heated __________ critical point.
C. Between the first & second
D. Between the second & third
What is the correct answer?
4
Which of the following does not have a sharp melting point?
What is the correct answer?
4
Production of one ton of paper in Indian paper industry consumes about __________ kWh of electricity.
What is the correct answer?
4
LVDT used for displacement measurement is a/an __________ transducer.
What is the correct answer?
4
Which of the following pairs is not correctly matched?
A. Uranium - 233 : Fertile material
B. Binding energy : Mass defect
C. Scattering: Absorption cross-section
D. Number of nucleons : Mass number
What is the correct answer?
4
Midrex process of sponge iron production uses reformed natural gas as the reducing agent, which uses iron ore in the form of
What is the correct answer?
4
__________ is the most important element, which controls the physical properties of steel.
What is the correct answer?
4
Thermal equivalent of electrical power in practical calculation is __________ kcal/kWh.