Related Questions
What is the correct answer?
4
A _________ routes between different autonomous systems.
What is the correct answer?
4
A __________ route is the best path to reach a destination within the topology table.
What is the correct answer?
4
Which command assigns a default gateway to the 2950 switch?
A. (config)# default-gateway
B. (config-if)# default-gateway
C. (config-if)# ip default-gateway
D. (config)# ip default-gateway
What is the correct answer?
4
Which IGRP command allows unequal-cost load balancing?
What is the correct answer?
4
You are given a Class B network with a subnet mask of 255.255.255.192. How many host
addresses are there on each subnet?
What is the correct answer?
4
VLSM allows a network segment to have more than one subnet mask.
What is the correct answer?
4
You are at User EXEC mode and type the letter e. What message appears?
C. % Unknown command or computer name
D. % Invalid input detected at '^'.
What is the correct answer?
4
Which of the following is true concerning bridges?
A. They switch frames in hardware.
B. They support half- and full-duplexing.
C. They support one collision domain for the entire bridge.
D. They do only store-and-forward switching.
What is the correct answer?
4
A _________ is used to connect networking devices that are in a very close geographic area, such as a floor of a building, a building itself, or a campus environment.
What is the correct answer?
4
Which of the following is false concerning VLANs?
A. A VLAN is a broadcast domain.
B. A VLAN is a logical group of users.
C. A VLAN is location-dependent.
What is the correct answer?
4
You are given this address space: 172.16.5.0/25. You need one network with 64 hosts and two with 30 hosts. What are the most specific subnet mask values to use?
What is the correct answer?
4
What would you use to prevent a packet from traveling around a routing loop forever?
What is the correct answer?
4
VLSM allows you to summarize __________ back to the class boundary.
What is the correct answer?
4
Which command takes you from Privilege EXEC mode to User EXEC mode?
What is the correct answer?
4
Which is not one of the three main functions of a layer-2 device?
What is the correct answer?
4
___________ has both physical and logical ring topologies.
What is the correct answer?
4
A Class A address has _________ host bits.
What is the correct answer?
4
Which prompt indicates that you are at User EXEC mode?
What is the correct answer?
4
IOS images can be loaded from all the following except:
What is the correct answer?
4
Which of the following is false concerning OSPF?
A. It provides a loop-free topology.
B. It is a classful protocol and allows for a hierarchical design.
C. It requires more memory and processing cycles than distance vector protocols.
D. It is complex to configure and difficult to troubleshoot.
What is the correct answer?
4
Which of the following is true concerning ISL?
A. It is supported on both the 1900 and 2950 switches.
B. It adds a 26-byte trailer and 4-byte header.
C. Tagging is done in software.
D. The original Ethernet frame is not modified.
What is the correct answer?
4
Which of the following is true concerning 802.1Q?
A. It supports hub connections.
B. It is supported on both the 1900 and 2950 switches.
C. The native VLAN is tagged.
D. The original Ethernet frame is not modified.
What is the correct answer?
4
________ topologies in NBMA environments do not have problems with split horizon.
What is the correct answer?
4
With a rollover cable, pin 7 on one end is mapped to pin ________ on the other end.
What is the correct answer?
4
There are _________ actions a router can take when there is a match on an ACL statement
What is the correct answer?
4
When configuring the ip nat inside source command, which parameter must you specify to perform PAT?
What is the correct answer?
4
If you see a VC with an inactive status, this indicates ____________.
A. The connection between both Frame Relay DTEs is up and operational.
B. The connection between your Frame Relay DTE and DCE is up and operational, but there is something wrong with connection between your connected Frame Relay switch and the destination DTE.
C. You are not receiving any LMI messages from the Frame Relay switch.
What is the correct answer?
4
OSPF hellos are sent every __________ seconds on a multi-access medium.
What is the correct answer?
4
Which command defines interesting traffic?
What is the correct answer?
4
When configuring a router-on-a-stick, the configuration is done on __________.