Related Questions
What is the correct answer?
4
Which of the following has the highest modulus of elasticity (about 7 × 106 kg/cm2)?
What is the correct answer?
4
Eutectic reaction for iron-carbon system occurs at a temperature of __________ °C.
What is the correct answer?
4
As per the Indian boiler regulation (IBR), the type of joint preferred for the circumferential joint is the __________ joint.
What is the correct answer?
4
When an isolated thermodynamic system executes a process,
B. Heat transfer takes place
C. Mass flow occurs across the boundary of the system
D. No chemical reaction takes place within the system
What is the correct answer?
4
Reynolds number of a fluid flowing in a circular pipe is 10,000. What will be the Reynolds number when the fluid velocity is decreased by 30% & the pipe diameter is increased by 30%?
What is the correct answer?
4
__________ is the most suitable lubricant for drawing mild steel wires?
What is the correct answer?
4
Heat flow across a hollow sphere of inner radius 'r1' and outer radius 'r2' is directly proportional to
What is the correct answer?
4
The type of pump used for lifting large quantity of sewage is a __________ pump.
What is the correct answer?
4
Sand used to stop the green sand from sticking to the pattern is termed as the __________ sand.
What is the correct answer?
4
Pressure exerted by a liquid depends upon its
What is the correct answer?
4
Which of the following is the most suitable material of construction for the condenser tubes, where the cooling medium is brine (salty water)?
What is the correct answer?
4
Potable water means the water used for
D. Evaporation to produce steam
What is the correct answer?
4
Solute atoms which cause yield point phenomenon in mild steel are/is
What is the correct answer?
4
Inertial forces are obtained, when the elastic forces are multiplied by __________ number.
What is the correct answer?
4
In the acid Bessemer process, the hot metal should have the following composition.
A. S < 0.05% and P < 0.05%
B. S < 0.05% and P < 1.5%
C. S < 0.05% and P > 1.5%
D. S > 1.5% and P < 0.05%
What is the correct answer?
4
The most important consideration, while designing the refrigeration system of an aircraft is that the refrigeration system
A. Is as light as possible
C. Employs minimum quantity of refrigerant
D. Consumer minimum horse power
What is the correct answer?
4
Most important property of steels for use in automobile bodies is the
What is the correct answer?
4
The taper provided on pattern for its easy & clean withdrawal from the mould is termed as the __________ allowance.
What is the correct answer?
4
Difference at any instant between the value of the controlled variable and the set point is called the
What is the correct answer?
4
The rolling process cannot be used to produce
What is the correct answer?
4
'GASOHOL' widely used in Brazil as a motor fuel is a mixture of alcohol and
C. Light hydrocarbon gases (e.g. butane or propane)
What is the correct answer?
4
Work hardenable alloy steel used to make the bucket wheel excavators, blades of bulldozers and other earth moving equipments contain iron, carbon and
What is the correct answer?
4
The capacity of a spring to store energy is called the spring form co-efficient. Stiffness of a spring is measured by the
A. Ability to absorb shock
B. Capacity to store energy
C. Ratio of the wire & coil diameters
D. Load to produce unit deflection
What is the correct answer?
4
In a good rimming steel
A. Carbon and silicon should be low
B. Silicon should be low but carbon should be high
C. Both silicon & carbon should be high
D. Silicon should be high but carbon should be low
What is the correct answer?
4
While the recrystallisation temperature for pure metals is 0.3 Tm, the same for alloys is equal to __________ × Tm (where, Tm Melting temperature).
What is the correct answer?
4
Which of the following terminology is used for the temperature at which new grains are formed in a metal?
B. Lower critical temperature
C. Recrystallisation temperature
D. Upper critical temperature
What is the correct answer?
4
Shaft/rotor speed is most accurately measured by a
What is the correct answer?
4
L.D. (Linz-Donawitz) converter is used in the production of
What is the correct answer?
4
Which of the following metals cannot be hot worked at room temperature?
What is the correct answer?
4
Use of water as a manometric liquid suffers from the disadvantage of its