Related Questions
What is the correct answer?
4
A material being tested for endurance strength is subjected to the __________ load.
What is the correct answer?
4
Milk is fat dispersed in water. It is an example of
What is the correct answer?
4
Wavelength of radiation emitted by a body depends on the __________ of its surface.
What is the correct answer?
4
The malleability of a material is the property by virtue of which it can be rolled or hammered into thin sheets. Which of the following materials has the maximum malleability?
What is the correct answer?
4
At the point of boundary layer separation in fluid flow, the
A. Shear stress is maximum
B. Velocity gradient is flat
C. Density variation is maximum
What is the correct answer?
4
Other parameters remaining same, the recrystallisation temperature of an alloy is lowered, when
A. Strain rate is increased
B. Grain size is increased
C. Prior cold deformation is increased
D. Not affected by any of the above parameters
What is the correct answer?
4
In extrusion of metals, which of the following statement is true?
A. Speed of the extruded material is same as that of ram speed
B. Redundant work is a function of the die angle
C. Relative motion between the billet surface and the container wall is always present
D. Hollow ram is used for indirect extrusion
What is the correct answer?
4
__________ test is the appropriate test to determine whether a material is ductile or brittle.
What is the correct answer?
4
Dryness factor of steam is defined as the ratio of the mass of vapor in the mixture to the mass of the mixture. Dryness factor of steam is measured by a __________ calorimeter.
What is the correct answer?
4
Increase in the entropy of a system represents the
B. Decrease in system pressure
C. Increase in the availability of energy
D. Increase in the temperature
What is the correct answer?
4
Addition of __________ to steel does not help in improving its machinability.
What is the correct answer?
4
Electrical conductivities of semi-conductors are of the order of __________ ohm/cm.
What is the correct answer?
4
Which of the following is not the function of a volute casing provided in a centrifugal pump?
A. To reduce the head loss in discharge
B. To increase the pump efficiency
C. To collect liquid from the periphery of the impeller and to transmit it to the delivery pipe at constant velocity
D. To increase the pump discharge rate
What is the correct answer?
4
Which of the following mainly decides the current to be employed is arc welding?
C. Voltage across the arc
What is the correct answer?
4
The ratio of the shear stress to the principal stress on a principal plane is
What is the correct answer?
4
Resilience of a bolt can be increased by increasing its
What is the correct answer?
4
Maximum permissible air velocity in pipelines is about __________ metre/second.
What is the correct answer?
4
A 2 kg object weighs 1.8 kgf on a spring balance. The value of 'g' at that location in m/sec2 is
What is the correct answer?
4
X-rays are
D. Of higher wavelength than visible light
What is the correct answer?
4
Solidification time of a molten metal in a casting is proportional to (where, V = volume of metal & A = its surface area; in the casting)
What is the correct answer?
4
Fire refining process is employed in case of
What is the correct answer?
4
The minimum carbon content in steel should be __________ percent for it to respond to a hardening treatment.
What is the correct answer?
4
The function of neutral flux used in the pyrometallurgy of metal extraction is to increase the __________ of the slag.
What is the correct answer?
4
Satellites burn off during re-entry to earth's atmosphere, because of the
B. Gravitational pull by earth
C. Friction with earth's atmosphere
D. Loss in weight of the satellite
What is the correct answer?
4
While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the
C. Better finish and surface appearance
D. High plastic deformation
What is the correct answer?
4
Lead pencil contains
What is the correct answer?
4
The friction factor for the turbulent fluid flow in a rough pipe does not depend upon the
A. Pipe roughness & pipe diameter
What is the correct answer?
4
In Imperial Smelting Process for extraction of zinc, zinc vapour thus produced is quenched in the external condenser by the use of the following:
A. Jet of water at high pressure
C. Mixture of water and air
What is the correct answer?
4
Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling.
What is the correct answer?
4
__________ of air does not increase with increase in temperature.