Related Questions
What is the correct answer?
4
What command creates a DHCP address pool on a router?
What is the correct answer?
4
Which command assigns a default gateway to the 2950 switch?
A. (config)# default-gateway
B. (config-if)# default-gateway
C. (config-if)# ip default-gateway
D. (config)# ip default-gateway
What is the correct answer?
4
Which of the following is false concerning OSPF?
A. It provides a loop-free topology.
B. It is a classful protocol and allows for a hierarchical design.
C. It requires more memory and processing cycles than distance vector protocols.
D. It is complex to configure and difficult to troubleshoot.
What is the correct answer?
4
Which of the following are classless protocols?
What is the correct answer?
4
The _________ reference point defines the connection between the NT2 and the NT1.
What is the correct answer?
4
With a rollover cable, pin 7 on one end is mapped to pin ________ on the other end.
What is the correct answer?
4
The _______ program goes out and finds the IOS and loads it.
What is the correct answer?
4
RIP has a maximum hop count of ____________ hops.
What is the correct answer?
4
If the 1900's mode is FDUP, and the LED is _________, the port speed is set to autodetect.
What is the correct answer?
4
Enter the wildcard mask value to match on every bit position in an address: _________.
What is the correct answer?
4
A Class A address has _________ host bits.
What is the correct answer?
4
Which of the following is the most expensive type of WAN connection?
A. Dedicated circuit connection
B. Circuit-switched connection
C. Packet-switched connection
What is the correct answer?
4
A _________ uses Gigabit Ethernet as a media type
What is the correct answer?
4
_________ negotiates the data link and network layer protocols that will traverse a PPP connection.
What is the correct answer?
4
Which of the following is true concerning full-duplexing?
A. It can either send or receive frames, but not both simultaneously.
B. It can be used with hubs.
C. It can be used with 10Base5 cabling.
D. It uses point-to-point connections.
What is the correct answer?
4
Private addressing is defined in RFC ______.
What is the correct answer?
4
Which of the following is a private address?
What is the correct answer?
4
You are given a class C network and you have four LAN segments with the following numbers of devices: 120, 60, and two with 30. What subnet mask values would you use to accommodate these segments?
What is the correct answer?
4
You are given this address space: 172.16.5.0/25. You need one network with 64 hosts and two with 30 hosts. What are the most specific subnet mask values to use?
What is the correct answer?
4
Which controller command specifies how ones and zeros are represented on a digital circuit?
What is the correct answer?
4
You are given a Class C network, 192.168.1.0/24. You need one network with 120 hosts
and two networks with 60 hosts. How many subnet masks do you need?
What is the correct answer?
4
IOS images can be loaded from all the following except:
What is the correct answer?
4
You execute the line console 0 command from Configuration mode. What will the router's prompt be?
C. Router(config-interface)#
What is the correct answer?
4
When configuring your terminal emulation software for a console connection, set the flow control to __________.
What is the correct answer?
4
An _____________ is a public IP address associated with an inside device.
A. Inside global IP address
B. Inside local IP address
C. Outside global IP address
D. Outside local IP address
What is the correct answer?
4
You are given a class C network, 192.168.1.0/24. You need three networks with 60 hosts and two networks with 30 hosts. What are the subnet mask values you could use?
A. 255.255.255.128 and 255.255.255.192
B. 255.255.255.224 and 255.255.255.240
C. 255.255.255.192 and 255.255.255.224
What is the correct answer?
4
The default encapsulation on a synchronous serial interface is _________.
What is the correct answer?
4
Which frame field is different between ISO HDLC and Cisco's HDLC?
What is the correct answer?
4
What must you do to enable IP routing on your router? (Choose all of the correct answers.)
A. Enable the routing protocol.
B. Set clocking on all serial interfaces.
C. Assign IP addresses to your router's interfaces.
D. Assign the bandwidth parameter to your serial interfaces
What is the correct answer?
4
Which command activates an IP ACL on a router's interface?