You are in Interface Subconfiguration mode and want to completely return to Privilege EXEC mode. What would you enter? (Choose all correct answers.)
CTRL-Z
end
exit
logout
Correct Answer :
A. CTRL-Z
Related Questions
A _________ is used to connect networking devices that are in a very close geographic area, such as a floor of a building, a building itself, or a campus environment.
WAN
LAN
MAN
LAN and MAN
Which Frame Relay command is used to manually resolve addresses?
frame-relay interface-dlci
frame-relay map
frame-relay resolve
frame-relay lmi-type
When backing up your IOS image from flash, which of the following will the copy flash tftp command prompt you for? (Choose all correct answers.)
TFTP server IP address
Verification to copy
Source filename
Destination filename
You have a 24-channel T1 connection to your router. How many VCs does this T1 support?
1
24
No limit
What command activates the IP routing process?
router
enable
network
no shutdown
Which VTP mode(s) will propagate VTP messages?
Client and server
Server
Client, server, and transparent
Transparent
Which of the following is the most expensive type of WAN connection?
Dedicated circuit connection
Circuit-switched connection
Packet-switched connection
Private addressing is defined in RFC ______.
1920
1934
1818
1918
You are given this address space: 172.16.5.0/25. You need one network with 64 hosts and two with 30 hosts. What are the most specific subnet mask values to use?
/25 and /26
/26 and /27
/27 and /28
None of these
___________ has both physical and logical ring topologies.
Ethernet
FDDI
Token Ring
Frames sent above the __________ limit will have their _________ bit set.
CIR, DE
BC, DE
BC, FECN
CIR, FECN
Distance vector protocols use ___________ to disseminate routing information.
Unicast
Multicast
Broadcast
Which metric components, by default, are used in IGRP? (Choose all the correct answers.)
Delay
Reliability
Load
Bandwidth
Which router command would take you back to a suspended telnet session?
reconnect
connect
resume
toggle
Which of the following situations are best for DDR connections?
Primary WAN connection
A lot of constant traffic
Long phone calls
Backup connection
Which of the following is true concerning RIPv2?
It uses triggered updates.
It uses broadcasts.
It is classful.
It doesn't support route summarization
The dialer map command contains all of the following parameters except __________.
Protocol name
Remote router name
Address of local router
Speed of the connection
EIGRP uses the _________ algorithm to update its routing table.
Bellman-Ford
Dijkstra
DUAL
Integrated
Which router command performs an overwrite process? (Choose all correct answers.)
copy running-config startup-config
copy startup-config running-config
copy tftp running-config
copy running-config tftp
Which type of traffic is not flooded?
Multicast
Known unicast
Broadcast
Unknown unicast
What would you enter to see the last few commands you entered?
show version
show commands
show previous
show history
_________ defines how the Frame Relay DTE and DCE interact with each other.
DLCI
CIR
LMI
PMI
__________ allows you to distribute connection requests destined to a single IP address to multiple machines.
Traffic load
Traffic configuration
PAT
Load distribution
A _________ provides a high-speed infrastructure to move data between storage devices and file servers.
SAN
LAN
CN
SAN and CN
There are _________ actions a router can take when there is a match on an ACL statement
1
2
3
4
_________ describe(s) users working from home.
SOHO
Branch office
Regional office
Corporate office
VLSM allows a network segment to have more than one subnet mask.
True
False
_________ has a physical star topology but a logical ring topology.
FDDI
Token Ring
Ethernet
FDDI and Token Ring
Which router-on-a-stick command defines the VLAN for the interface?
vlan
encapsulation
trunk
frame-type
Cisco routers generate LMI enquiries every _______ seconds and a full status update every _________ seconds.
10, 60
10, 6
60, 300
15, 60