Related Questions
What is the correct answer?
4
Which router command clears all of the static translations in the address translation table?
A. erase ip nat translation *
B. clear ip nat translation *
C. clear ip nat translation all
D. None of these commands
What is the correct answer?
4
Which of the following is the most expensive type of WAN connection?
A. Dedicated circuit connection
B. Circuit-switched connection
C. Packet-switched connection
What is the correct answer?
4
Which of the following is true concerning 802.1Q?
A. It supports hub connections.
B. It is supported on both the 1900 and 2950 switches.
C. The native VLAN is tagged.
D. The original Ethernet frame is not modified.
What is the correct answer?
4
___________ only translates one (and only one) IP address to another.
What is the correct answer?
4
Which of the following commands belongs on the physical interface when using dialer profiles?
What is the correct answer?
4
A routing protocol that supports route summarization must perform all except which of the following?
A. Carry the subnet mask with the network entry.
B. Make routing decisions based on the entire destination IP address.
C. Summarize entries so that the same lowest-order bits match.
What is the correct answer?
4
Which type of routing protocol uses the Shortest Path First algorithm?
What is the correct answer?
4
The switch port that is chosen to forward traffic for a segment is called a __________.
What is the correct answer?
4
A _________ provides a high-speed infrastructure to move data between storage devices and file servers.
What is the correct answer?
4
A routing protocol will use a _________ to determine which path is the best path.
A. Administrative distance
What is the correct answer?
4
Which control sequence moves the cursor to the end of the line?
What is the correct answer?
4
You are given the following addressing information: 172.17.16.255/23. What type of address is this?
What is the correct answer?
4
Which of the following is true concerning RIPv2?
A. It uses triggered updates.
D. It doesn't support route summarization
What is the correct answer?
4
Which router command would take you back to a suspended telnet session?
What is the correct answer?
4
What command activates the IP routing process?
What is the correct answer?
4
VLSM allows you to summarize __________ back to the class boundary.
What is the correct answer?
4
When connecting a switch to a router, use a ___________ cable.
What is the correct answer?
4
Which frame field is different between ISO HDLC and Cisco's HDLC?
What is the correct answer?
4
When backing up your IOS image from flash, which of the following will the copy flash tftp command prompt you for? (Choose all correct answers.)
A. TFTP server IP address
What is the correct answer?
4
Which command assigns a default gateway to the 2950 switch?
A. (config)# default-gateway
B. (config-if)# default-gateway
C. (config-if)# ip default-gateway
D. (config)# ip default-gateway
What is the correct answer?
4
You are given a Class C network, 192.168.1.0/24. You need one network with 120 hosts
and two networks with 60 hosts. How many subnet masks do you need?
What is the correct answer?
4
The address of a Frame Relay VC is called a ___________.
A. Data link layer connection identifier
B. Data layer connection index
C. Data link connection index
D. Data link connection identifier
What is the correct answer?
4
Which is not one of the three main functions of a layer-2 device?
What is the correct answer?
4
Which IGRP command allows unequal-cost load balancing?
What is the correct answer?
4
Enter the wildcard mask value to match on every bit position in an address: _________.
What is the correct answer?
4
Which protocol supports VLSM?
What is the correct answer?
4
Which of the following is a Network layer protocol for the TCP/IP protocol stack?
What is the correct answer?
4
Private addressing is defined in RFC ______.
What is the correct answer?
4
Which prompt indicates that you are at User EXEC mode?
What is the correct answer?
4
When using the show interfaces command, which Frame Relay information can you not see?
A. The DLCI number used for LMI
B. The number of LMIs sent and received