You have this binary value: 11000001. This equates to _____ in decimal.
183
193
173
203
Correct Answer :
B. 193
Related Questions
Which of the following situations are best for DDR connections?
Primary WAN connection
A lot of constant traffic
Long phone calls
Backup connection
Which of the following is true concerning 802.1Q?
It supports hub connections.
It is supported on both the 1900 and 2950 switches.
The native VLAN is tagged.
The original Ethernet frame is not modified.
Which of the following is stored in ROM? (Choose all correct answers.)
POST
ROMMON
Configuration file
System recovery file
A _________ uses Gigabit Ethernet as a media type
WAN
LAN
MAN
LAN and MAN
Which of the following reasons might you need to use address translation?
You have to use public addressing because your ISP didn't assign you enough private addresses.
You are using private addresses but have changed ISPs, and your new ISP won't support these private addresses.
You want to assign the same IP address to multiple machines so that users on the Internet see this offered service as a single logical computer.
You are merging two companies that use different address spaces.
You have ISL trunks in your network and five VLANs configured. How many instances of STP are running?
1
5
10
15
Extended IP ACLs should be placed as close to the ____________ device as possible.
Source
Destination
When backing up your IOS image from flash, which of the following will the copy flash tftp command prompt you for? (Choose all correct answers.)
TFTP server IP address
Verification to copy
Source filename
Destination filename
The 1900 switch supports ________ VLANs.
10
32
64
250
_________ allows you to create this summarization: 10.0.0.0/7.
Subnetting
CDR
Supernetting
VLSM
With a rollover cable, pin 7 on one end is mapped to pin ________ on the other end.
2
3
4
5
Which of the following is true concerning full-duplexing?
It can either send or receive frames, but not both simultaneously.
It can be used with hubs.
It can be used with 10Base5 cabling.
It uses point-to-point connections.
Which interface type is used to connect to the serial interface of a router?
EIA/TIA-232
V.35
DB-60
X.21
What subnet mask would you use to set up a default route?
0.0.0.0
255.255.255.255
Depends on the type of network number
None of these answers
__________ allows you to distribute connection requests destined to a single IP address to multiple machines.
Traffic load
Traffic configuration
PAT
Load distribution
With a crossover cable, which pins are crossed over?
1 and 2, 3 and 6
1 and 3, 2 and 6
1 and 4, 2 and 6
1 and 3, 4 and 6
___________ only translates one (and only one) IP address to another.
NAT
PAT
PAR
NAT and PAT
_________ is/are a routed protocol.
RIP
OSPF
Both RIP and OSPF
Neither RIP or OSPF
Which of the following is the most expensive type of WAN connection?
Dedicated circuit connection
Circuit-switched connection
Packet-switched connection
Which VTP mode(s) will propagate VTP messages?
Client and server
Server
Client, server, and transparent
Transparent
Which command defines interesting traffic?
dialer-group
dialer-list
dialer map
dialer remote-name
How many steps do LCP and NCP go through when setting up a connection?
1
2
3
4
You are given the following addressing information: 172.17.16.255/23. What type of address is this?
Network
Directed Broadcast
Host
If you wanted a list of parameters for the show command, you would type ________.
LOOK
VIEW
SHOW
RIP has a maximum hop count of ____________ hops.
10
15
16
100
Which of the following is true concerning bridges?
They switch frames in hardware.
They support half- and full-duplexing.
They support one collision domain for the entire bridge.
They do only store-and-forward switching.
Which type of traffic is sent to a group of devices?
Multicast
Unicast
Broadcast
Groupcast
You have a 24-channel T1 connection to your router. How many VCs does this T1 support?
1
24
No limit
Which is an example of a hybrid protocol?
IGRP
EIGRP
RIPv1
OSPF
How would you suspend a telnet session?
CTRL-SHIFT-X 6
CTRL-SHIFT-6 X
CTRL-6 X
CTRL-C