1000+ Hydraulics & Fluid Machineries MCQ for NEET PG [Solved]

1. In an outward flow reaction turbine
A. The water flows parallel to the axis of the wheel
B. The water enters at the centre of the wheel and then flows towards the outer periphery of the wheel
C. The water enters the wheel at the outer periphery and then flows towards the centre of the wheel
D. The flow of water is partly radial and partly axial
Answer : B

2. The jet ratio is defined as the ratio of the
A. Diameter of jet to the diameter of Pelton wheel
B. Velocity of jet to the velocity of Pelton wheel
C. Diameter of Pelton wheel to the diameter of jet
D. Velocity of Pelton wheel to the velocity of jet
Answer : C

3. The hydraulic efficiency of an impulse turbine is maximum when velocity of wheel is _______ of the jet velocity,
A. One-fourth
B. One-half
C. Three-fourth
D. Double
Answer : B

4. The Thomson's turbine is __________ reaction turbine.
A. An axial flow
B. An inward flow
C. An outward flow
D. A mixed flow
Answer : B

5. Which of the following is not an impulse turbine?
A. Girad turbine
B. Turgo turbine
C. Pelton wheel
D. Kaplan turbine
Answer : D

6. The specific speed from 160 to 500 r.p.m. of a centrifugal pump indicates that the pump is
A. Slow speed with radial flow at outlet
B. Medium speed with radial flow at outlet
C. High speed with radial flow at outlet
D. High speed with axial flow at outlet
Answer : D

7. In a reaction turbine, the draft tube is used
A. To run the turbine full
B. To prevent air to enter the turbine
C. To increase the head of water by an amount equal to the height of the runner outlet above the tail race
D. To transport water to downstream
Answer : C

8. If a pump is handling water and is discharging a certain flow Q at a constant total dynamic head requiring a definite B.H.P., the same pump when handling a liquid of specific gravity 0.75 and viscosity nearly same as of water, the horse power required will be
A. Same
B. 0.75 B.H.P.
C. B.H.P./0.75
D. 1.5 B.H.P.
Answer : B

9. Which of the following pump is successfully used for lifting water to the turbines?
A. Centrifugal pump
B. Reciprocating pump
C. Jet pump
D. Air lift pump
Answer : C

10. A hydraulic press is a device used
A. To store pressure energy which may be supplied to a machine later on
B. To increase the intensity of pressure of water by means of energy available from a large quantity of water at a low pressure
C. To lift larger load by the application of a comparatively much smaller force
D. All of the above
Answer : C

11. Air vessels in reciprocating pump are used to
A. Smoothen flow
B. Reduce acceleration to minimum
C. Increase pump efficiency
D. Save pump from cavitations
Answer : B

12. The force exerted (in Newton) by a jet of water impinging normally on a fixed plate is (where w = Specific weight of water in N/m3, a = Crosssectional area of jet in m², and V = Velocity of jet in m/s)
A. waV / 2g
B. waV / g
C. waV² / 2g
D. waV² / g
Answer : D

13. Reaction turbines are used for
A. Low head
B. High head
C. High head and low discharge
D. Low head and high discharge
Answer : D

14. Head developed by a centrifugal pump depends on
A. Impeller diameter
B. Speed
C. Fluid density
D. Both (A) and (B) above
Answer : D

15. The specific speed (Ns) of a centrifugal pump is given by
A. (N?Q)/H^2/3
B. (N?Q)/H^3/4
C. (N?Q)/H
D. (N?Q)/H^5/4
Answer : B

16. A jet of water is striking at the centre of a curved vane moving with a uniform velocity in the direction of jet. For the maximum efficiency, the vane velocity is ________ of the jet velocity
A. One-half
B. One-third
C. Two-third
D. Three-fourth
Answer : B

17. A turbine is required to develop 1500 kW at 300 r.p.m. under a head of 150 m. Which of the following turbine should be used?
A. Pelton wheel with one nozzle
B. Pelton wheel with two or more nozzles
C. Kaplan turbine
D. Francis turbine
Answer : A

18. Puck up the wrong statement about centrifugal pump
A. Discharge a diameter
B. Head a speed²
C. Head a diameter
D. Power a speed?
Answer : A

19. The water in a jet propelled boat is drawn through the openings facing the direction of motion of the boat. The efficiency of propulsion is given by
A. 2V/(v_r - v)
B. 2V/(v_r + v)
C. V/(v_r - v)
D. V/(v_r + v)
Answer : B

20. The impeller of a centrifugal pump may have
A. Volute casing
B. Volute casing with guide blades
C. Vortex casing
D. Any one of these
Answer : D

21. In a centrifugal pump, the liquid enters the pump
A. At the top
B. At the bottom
C. At the canter
D. From sides
Answer : C

22. The force exerted by a jet of water (in a direction normal to flow) impinging on a fixed plate inclined at an angle ? with the jet is
A. waV/2g × sin?
B. waV/g × sin?
C. waV²/2g × sin2?
D. waV²/g × sin?
Answer : C

23. The Fourneyron turbine is _________ reaction turbine.
A. An axial flow
B. An inward flow
C. An outward flow
D. A mixed flow
Answer : C

24. The cavitation in reaction turbines is avoided, to a great extent by
A. Installing the turbine below the tail race level
B. Using stainless steel runner of the turbine
C. Providing highly polished blades to the runner
D. All of the above
Answer : D

25. In a centrifugal pump casing, the flow of water leaving the impeller, is
A. Rectilinear flow
B. Radial flow
C. Free vortex motion
D. Forced vortex
Answer : C

26. Dynamic similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. None of the above
Answer : D

27. In a Kaplan turbine runner, the numbers of blades are generally between
A. 2 to 4
B. 4 to 8
C. 8 to 16
D. 16 to 24
Answer : B

28. Centrifugal pump is started with its delivery valve
A. Kept fully closed
B. Kept fully open
C. Irrespective of any position
D. Kept 50% open
Answer : A

29. A double overhung Pelton wheel has
A. Two jets
B. Two runners
C. Four jets
D. Four runners
Answer : B

30. Which of the following pump is suitable for small discharge and high heads?
A. Centrifugal pump
B. Axial flow pump
C. Mixed flow pump
D. Reciprocating pump
Answer : D

31. The speed of an imaginary turbine, identical with the given turbine, which will develop a unit power under a unit head, is known as
A. Normal speed
B. Unit speed
C. Specific speed
D. None of these
Answer : C

32. Which of the following statement is correct as regard to water wheels?
A. They have slow speeds
B. They are suitable even for low water heads
C. They give constant efficiency, even if the discharge is not constant
D. All of the above
Answer : D

33. In a Francis turbine runner, the numbers of blades are generally between
A. 2 to 4
B. 4 to 8
C. 8 to 16
D. 16 to 24
Answer : D

34. Which of the following hydraulic unit is used for transmitting increased or decreased torque to the driven shaft?
A. Hydraulic ram
B. Hydraulic intensifier
C. Hydraulic torque converter
D. Hydraulic accumulator
Answer : C

35. By fitting an air vessel to the reciprocating pump, there is always a saving of work done and subsequently saving of power. The saving in case of a double acting reciprocating pump is
A. 39.2 %
B. 48.8 %
C. 84.8 %
D. 88.4 %
Answer : A

36. Head developed by a centrifugal pump is
A. Proportional to diameter of impeller
B. Proportional to speed of impeller
C. Proportional to diameter and speed of impeller
D. None of the above
Answer : C

37. In a centrifugal pump, the regulating valve is provided on the
A. Casing
B. Delivery pipe
C. Suction pipe
D. Impeller
Answer : B

38. An impulse turbine is used for
A. Low head of water
B. High head of water
C. Medium head of water
D. High discharge
Answer : B

39. Reciprocating pumps are no more to be seen in industrial applications (in comparison to centrifugal pumps) because of
A. High initial and maintenance cost
B. Lower discharge
C. Lower speed of operation
D. Necessity of air vessel
Answer : A

40. The efficiency of a Pelton wheel working under constant head ________ with the increase in power.
A. Remain same
B. Increases
C. Decreases
D. None of these
Answer : B

41. The discharge through a turbine is
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : A

42. The static head of a centrifugal pump is equal to the ________ of suction head and delivery head.
A. Product
B. Difference
C. Sum
D. None of these
Answer : C

43. The cavitation in a hydraulic machine is mainly due to
A. Low velocity
B. High velocity
C. Low pressure
D. High pressure
Answer : C

44. When a piping system is made up primarily of friction head and very little of vertical lift, then pump characteristics should be
A. Horizontal
B. Nearly horizontal
C. Steep
D. First rise and then fall
Answer : B

45. If the ratios of all the corresponding linear dimensions are equal, then the model and the prototype are said to have
A. Geometric similarity
B. Kinematic similarity
C. Dynamic similarity
D. None of these
Answer : A

46. The specific speed of a centrifugal pump, delivering 750 litres of water per second against a head of 15 metres at 725 r.p.m., is
A. 24.8 r.p.m.
B. 48.2 r.p.m
C. 82.4 r.p.m.
D. 248 r.p.m
Answer : C

47. In a single casing, multistage pump running at constant speed, the capacity rating is to be slightly lowered. It can be done by
A. Designing new impeller
B. Trimming the impeller size to the required size by machining
C. Not possible
D. Some other alterations in the impeller
Answer : B

48. According to fan laws, for fans having constant wheel diameter, the pressure varies
A. Directly as fan speed
B. Square of fan speed
C. Cube of fan speed
D. Square root of fan speed
Answer : B

49. Which of the following is not a reaction turbine?
A. Fourneyron turbine
B. Journal turbine
C. Thomson's turbine
D. Pelton wheel
Answer : D

50. A Francis turbine is used when the available head of water is
A. 0 to 25 m
B. 25 m to 250 m
C. Above 250 m
D. None of these
Answer : B