1000+ Hydraulics & Fluid Machineries Multiple Choice Question Answer [Solved]

1. A jet of water is striking at the centre of a curved vane moving with a uniform velocity in the direction of jet. For the maximum efficiency, the vane velocity is ________ of the jet velocity
A. One-half
B. One-third
C. Two-third
D. Three-fourth
Answer : B

2. The flow ratio of Francis turbine is defined as the ratio of the
A. Velocity of flow at inlet to the theoretical jet velocity
B. Theoretical velocity of jet to the velocity of flow at inlet
C. Velocity of runner at inlet to the velocity of flow at inlet
D. None of the above
Answer : A

3. Reaction turbines are used for
A. Low head
B. High head
C. High head and low discharge
D. Low head and high discharge
Answer : D

4. The maximum number of jets generally employed in impulse turbine without jet interference is
A. 4
B. 6
C. 8
D. 12
Answer : B

5. Manometric head, in case of a centrifugal pump, is equal to
A. Suction lift + Loss of head in suction pipe due to friction + Delivery lift + Loss of head in delivery pipe due to friction + Velocity head in the delivery pipe
B. Workdone per kN of water Losses within the impeller
C. Energy per kN at outlet of impeller Energy per kN at inlet of impeller
D. All of the above
Answer : D

6. Which of the following pump is generally used to pump highly viscous fluid?
A. Centrifugal pump
B. Reciprocating pump
C. Air lift pump
D. Screw pump
Answer : D

7. A Francis turbine is used when the available head of water is
A. 0 to 25 m
B. 25 m to 250 m
C. Above 250 m
D. None of these
Answer : B

8. Indicator diagram of a reciprocating pump is a graph between
A. Flow vs. swept volume
B. Pressure in cylinder vs. swept volume
C. Flow vs. speed
D. Pressure vs. speed
Answer : B

9. The speed of an imaginary turbine, identical with the given turbine, which will develop a unit power under a unit head, is known as
A. Normal speed
B. Unit speed
C. Specific speed
D. None of these
Answer : C

10. The discharge through a turbine is
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : A

11. For small discharge at high pressure, following pump is preferred
A. Centrifugal
B. Axial flow
C. Mixed flow
D. Reciprocating
Answer : D

12. The specific speed of a turbine is given by the equation
A. N?P / H^3/2
B. N?P / H²
C. N?P / H^5/4
D. N?P / H³
Answer : C

13. The depth of the bucket for a Pelton wheel is generally ________ the diameter of jet.
A. Equal to
B. 1.2 times
C. 1.8 times
D. Double
Answer : B

14. The specific speed of a centrifugal pump, delivering 750 litres of water per second against a head of 15 metres at 725 r.p.m., is
A. 24.8 r.p.m.
B. 48.2 r.p.m
C. 82.4 r.p.m.
D. 248 r.p.m
Answer : C

15. The Fourneyron turbine is _________ reaction turbine.
A. An axial flow
B. An inward flow
C. An outward flow
D. A mixed flow
Answer : C

16. The number of buckets on the periphery of a Pelton wheel is given by
A. (D/2d) + 5
B. (D/2d) + 10
C. (D/2d) + 15
D. (D/2d) + 20
Answer : C

17. Kinematic similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. Have identical forces
Answer : A

18. According to fan laws, for the fans having constant wheel diameters, the power demand varies
A. Directly as fan speed
B. Square of fan speed
C. Cube of fan speed
D. Square root of fan speed
Answer : C

19. Low specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. Any one of the above
Answer : C

20. In a reaction turbine, the draft tube is used
A. To run the turbine full
B. To prevent air to enter the turbine
C. To increase the head of water by an amount equal to the height of the runner outlet above the tail race
D. To transport water to downstream
Answer : C

21. In a Kaplan turbine runner, the numbers of blades are generally between
A. 2 to 4
B. 4 to 8
C. 8 to 16
D. 16 to 24
Answer : B

22. Mechanical efficiency of a centrifugal pump is the ratio of
A. Energy available at the impeller to the energy supplied to the pump by the prime mover
B. Actual workdone by the pump to the energy supplied to the pump by the prime mover
C. Energy supplied to the pump to the energy available at the impeller
D. Manometric head to the energy supplied by the impeller per kN of water
Answer : A

23. Any change in load is adjusted by adjusting following parameter on turbine
A. Net head
B. Absolute velocity
C. Blade velocity
D. Flow
Answer : D

24. The cavitation in a hydraulic machine is mainly due to
A. Low velocity
B. High velocity
C. Low pressure
D. High pressure
Answer : C

25. The unit discharge through the turbine is
A. Q/?H
B. Q/H
C. Q/H^3/2
D. Q/H²
Answer : A

26. The maximum efficiency of jet propulsion of a ship with inlet orifices at right angles to the direction of motion of ship, is
A. 40 %
B. 50 %
C. 60 %
D. 80 %
Answer : B

27. Saving of work done and power by fitting an air vessel to double acting reciprocating pump is of the order of
A. 39.2 %
B. 49.2 %
C. 68.8 %
D. 84.8 %
Answer : A

28. Runaway speed of a hydraulic turbine is
A. Full load speed
B. The speed at which turbine runner will be damaged
C. The speed if the turbine runner is allowed to revolve freely without load and with the wicket gates wide open
D. The speed corresponding to maximum overload permissible
Answer : C

29. Discharge of a centrifugal pump is (where N = Speed of the pump impeller)
A. Directly proportional to N
B. Inversely proportional to N
C. Directly proportional to N²
D. Inversely proportional to N²
Answer : A

30. In an inward flow reaction turbine
A. The water flows parallel to the axis of the wheel
B. The water enters at the centre of the wheel and then flows towards the outer periphery of the wheel
C. The water enters the wheel at the outer periphery and then flows towards the centre of the wheel
D. The flow of water is partly radial and partly axial
Answer : C

31. Francis turbine is best suited for
A. Medium head application from 24 to 180 m
B. Low head installation up to 30 m
C. High head installation above 180 m
D. All types of heads
Answer : A

32. Multistage centrifugal pumps are used to obtain
A. High discharge
B. High head
C. Pumping of viscous fluids
D. High head and high discharge
Answer : B

33. The maximum number of jets, generally, employed in an impulse turbine without jet interference are
A. Two
B. Four
C. Six
D. Eight
Answer : C

34. In an outward flow reaction turbine
A. The water flows parallel to the axis of the wheel
B. The water enters at the centre of the wheel and then flows towards the outer periphery of the wheel
C. The water enters the wheel at the outer periphery and then flows towards the centre of the wheel
D. The flow of water is partly radial and partly axial
Answer : B

35. Which of the following statement is correct?
A. The centrifugal pump is suitable for large discharge and smaller heads.
B. The centrifugal pump requires less floor area and simple foundation as compared to reciprocating pump.
C. The efficiency of centrifugal pump is less as compared to reciprocating pump.
D. All of the above
Answer : D

36. Head developed by a centrifugal pump depends on
A. Impeller diameter
B. Speed
C. Fluid density
D. Both (A) and (B) above
Answer : D

37. A turbine develops 10000 kW under a head of 25 metres at 135 r.p.m. Its specific speed is
A. 175.4 r.p.m.
B. 215.5 r.p.m.
C. 241.5 r.p.m.
D. 275.4 r.p.m
Answer : C

38. The unit power developed by a turbine is (where P = Power developed by the turbine under a head of water (H).
A. P/ ?H
B. P/ H
C. P/ H^3/2
D. P/ H²
Answer : C

39. If a pump is handling water and is discharging a certain flow Q at a constant total dynamic head requiring a definite B.H.P., the same pump when handling a liquid of specific gravity 0.75 and viscosity nearly same as of water would discharge
A. Same quantity of liquid
B. 0.75 Q
C. Q/0.75
D. 1.5 Q
Answer : A

40. The Thomson's turbine is __________ reaction turbine.
A. An axial flow
B. An inward flow
C. An outward flow
D. A mixed flow
Answer : B

41. An impulse turbine is used for
A. Low head of water
B. High head of water
C. Medium head of water
D. High discharge
Answer : B

42. In a centrifugal pump casing, the flow of water leaving the impeller, is
A. Rectilinear flow
B. Radial flow
C. Free vortex motion
D. Forced vortex
Answer : C

43. According to fan laws, at constant speed and capacity, the pressure and power vary
A. Directly as the air or gas density
B. Inversely as square root of density
C. Inversely as density
D. As square of density
Answer : A

44. Braking jet in an impulse turbine is used
A. To break the jet of water
B. To bring the runner to rest in a short time
C. To change the direction of runner
D. None of these
Answer : B

45. The efficiency of a Pelton wheel working under constant head ________ with the increase in power.
A. Remain same
B. Increases
C. Decreases
D. None of these
Answer : B

46. In a centrifugal pump, the liquid enters the pump
A. At the top
B. At the bottom
C. At the canter
D. From sides
Answer : C

47. The ratio of actual work available at the turbine to the energy imparted to the wheel is known as ________ efficiency.
A. Hydraulic
B. Mechanical
C. Overall
D. None of these
Answer : B

48. The speed of a turbine runner is
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : A

49. A double overhung Pelton wheel has
A. Two jets
B. Two runners
C. Four jets
D. Four runners
Answer : B

50. A hydraulic accumulator normally consists of
A. Two cylinders, two rams and a storage device
B. A cylinder and a ram
C. Two coaxial rams and two cylinders
D. A cylinder, a piston, storage tank and control valve
Answer : B