Hydraulics & Fluid Machineries 1000+ MCQ with answer for SBI PO

1. The jet ratio is defined as the ratio of the
A. Diameter of jet to the diameter of Pelton wheel
B. Velocity of jet to the velocity of Pelton wheel
C. Diameter of Pelton wheel to the diameter of jet
D. Velocity of Pelton wheel to the velocity of jet
Answer : C

2. The cavitation in a hydraulic machine is mainly due to
A. Low velocity
B. High velocity
C. Low pressure
D. High pressure
Answer : C

3. The force exerted (in Newton) by a jet of water impinging normally on a fixed plate is (where w = Specific weight of water in N/m3, a = Crosssectional area of jet in m², and V = Velocity of jet in m/s)
A. waV / 2g
B. waV / g
C. waV² / 2g
D. waV² / g
Answer : D

4. The specific speed (Ns) of a centrifugal pump is given by
A. (N?Q)/H^2/3
B. (N?Q)/H^3/4
C. (N?Q)/H
D. (N?Q)/H^5/4
Answer : B

5. The speed of an imaginary turbine, identical with the given turbine, which will develop a unit power under a unit head, is known as
A. Normal speed
B. Unit speed
C. Specific speed
D. None of these
Answer : C

6. Saving of work done and power by fitting an air vessel to single acting reciprocating pump is of the order of
A. 39.2 %
B. 49.2 %
C. 68.8 %
D. 84.8 %
Answer : D

7. The optimum value of vane exit angle for a centrifugal pump impeller is
A. 10-15°
B. 20-25°
C. 30-40°
D. 50-60°
Answer : B

8. The specific speed of a centrifugal pump, delivering 750 litres of water per second against a head of 15 metres at 725 r.p.m., is
A. 24.8 r.p.m.
B. 48.2 r.p.m
C. 82.4 r.p.m.
D. 248 r.p.m
Answer : C

9. In a centrifugal pump casing, the flow of water leaving the impeller, is
A. Rectilinear flow
B. Radial flow
C. Free vortex motion
D. Forced vortex
Answer : C

10. The unit power developed by a turbine is (where P = Power developed by the turbine under a head of water (H).
A. P/ ?H
B. P/ H
C. P/ H^3/2
D. P/ H²
Answer : C

11. The ratio of actual work available at the turbine to the energy imparted to the wheel is known as ________ efficiency.
A. Hydraulic
B. Mechanical
C. Overall
D. None of these
Answer : B

12. The force exerted by a jet of water (in a direction normal to flow) impinging on a fixed plate inclined at an angle ? with the jet is
A. waV/2g × sin?
B. waV/g × sin?
C. waV²/2g × sin2?
D. waV²/g × sin?
Answer : C

13. If a pump is handling water and is discharging a certain flow Q at a constant total dynamic head requiring a definite B.H.P., the same pump when handling a liquid of specific gravity 0.75 and viscosity nearly same as of water, the horse power required will be
A. Same
B. 0.75 B.H.P.
C. B.H.P./0.75
D. 1.5 B.H.P.
Answer : B

14. The force exerted by a jet of water impinging normally on a plate which due to the impact of jet, moves in the direction of jet with a velocity v is
A. [wa (V - v)]/2g
B. [wa (V - v)]/g
C. [wa (V - v)²]/2g
D. [wa (V - v²)]/g
Answer : D

15. Discharge of a centrifugal pump is
A. Directly proportional to diameter of its impeller
B. Inversely proportional to diameter of its impeller
C. Directly proportional to (diameter)² of its impeller
D. Inversely proportional to (diameter)² of its impeller
Answer : D

16. Which of the following is not an impulse turbine?
A. Girad turbine
B. Turgo turbine
C. Pelton wheel
D. Kaplan turbine
Answer : D

17. The ratio of quantity of liquid discharged per second from the pump to the quantity of liquid passing per second through the impeller is known as
A. Manometric efficiency
B. Mechanical efficiency
C. Overall efficiency
D. Volumetric efficiency
Answer : D

18. Air vessels in reciprocating pump are used to
A. Smoothen flow
B. Reduce acceleration to minimum
C. Increase pump efficiency
D. Save pump from cavitations
Answer : B

19. In an inward flow reaction turbine
A. The water flows parallel to the axis of the wheel
B. The water enters at the centre of the wheel and then flows towards the outer periphery of the wheel
C. The water enters the wheel at the outer periphery and then flows towards the centre of the wheel
D. The flow of water is partly radial and partly axial
Answer : C

20. For very high discharge at low pressure such as for flood control and irrigation applications, following type of pump is preferred
A. Centrifugal
B. Axial flow
C. Reciprocating
D. Mixed flow
Answer : B

21. The depth of the bucket for a Pelton wheel is generally ________ the diameter of jet.
A. Equal to
B. 1.2 times
C. 1.8 times
D. Double
Answer : B

22. A turbine pump is basically a centrifugal pump equipped additionally with
A. Adjustable blades
B. Backward curved blades
C. Vaned diffusion casing
D. Inlet guide blades
Answer : C

23. A ship with jet propulsion draws water through inlet orifices at right angles to the direction of its motion. The propelling force of the jet is (where a = Area of the jet, Vr = Relative velocity of the jet and ship = V + v, v = Velocity of the ship, and V = Velocity of the jet issuing from the ship)
A. waVr /g × (Vr + v)
B. waVr /g × (Vr - v)
C. waVr /g × (Vr + v)²
D. waVr /g × (Vr - v)²
Answer : B

24. The overall efficiency for a Pelton wheel lies between
A. 0.50 to 0.65
B. 0.65 to 0.75
C. 0.75 to 0.85
D. 0.85 to 0.90
Answer : D

25. The function of guide vanes in a reaction turbine is to
A. Allow the water to enter the runner without shock
B. Allow the water to flow over them, without forming eddies
C. Allow the required quantity of water to enter the turbine
D. All of the above
Answer : D

26. Casting of a centrifugal pump is designed so as to minimize
A. Friction loss
B. Cavitations
C. Static head
D. Loss of kinetic energy
Answer : D

27. The flow ratio in case of Francis turbine varies from
A. 0.15 to 0.3
B. 0.4 to 0.5
C. 0.6 to 0.9
D. 1 to 1.5
Answer : A

28. Which of the following is not a reaction turbine?
A. Fourneyron turbine
B. Journal turbine
C. Thomson's turbine
D. Pelton wheel
Answer : D

29. In a centrifugal pump, the liquid enters the pump
A. At the top
B. At the bottom
C. At the canter
D. From sides
Answer : C

30. Maximum impulse will be developed in hydraulic ram when
A. Waste valve closes suddenly
B. Supply pipe is long
C. Supply pipe is short
D. Ram chamber is large
Answer : A

31. Which of the following statement is wrong?
A. The reaction turbines are used for low head and high discharge.
B. The angle of taper on draft tube is less than 8°.
C. An impulse turbine is generally fitted slightly above the tail race.
D. A Francis turbine is an impulse turbine.
Answer : D

32. Power required to drive a centrifugal pump is directly proportional to ________ of its impeller.
A. Diameter
B. Square of diameter
C. Cube of diameter
D. Fourth power of diameter
Answer : D

33. Dynamic similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. None of the above
Answer : D

34. Mechanical efficiency of a centrifugal pump is the ratio of
A. Energy available at the impeller to the energy supplied to the pump by the prime mover
B. Actual workdone by the pump to the energy supplied to the pump by the prime mover
C. Energy supplied to the pump to the energy available at the impeller
D. Manometric head to the energy supplied by the impeller per kN of water
Answer : A

35. The flow ratio of Francis turbine is defined as the ratio of the
A. Velocity of flow at inlet to the theoretical jet velocity
B. Theoretical velocity of jet to the velocity of flow at inlet
C. Velocity of runner at inlet to the velocity of flow at inlet
D. None of the above
Answer : A

36. For centrifugal pump impeller, the maximum value of the vane exit angle is
A. 10° to 15°
B. 15° to 20°
C. 20° to 25°
D. 25° to 30°
Answer : C

37. By fitting an air vessel to the reciprocating pump, there is always a saving of work done and subsequently saving of power. The saving in case of a double acting reciprocating pump is
A. 39.2 %
B. 48.8 %
C. 84.8 %
D. 88.4 %
Answer : A

38. The efficiency of a hydraulic press is given by (where W = Weight lifted by ram, P = Force applied on plunger, A = Area of ram, and a = Area of plunger)
A. (W/p) × (A/a)
B. (p/W) × (a/A)
C. (W/p) × (a/A)
D. (p/W) × (A/a)
Answer : C

39. The centrifugal pump preferred for a specific speed between 80 to 160 r.p.m. is
A. Slow speed with radial flow at outlet
B. Medium speed with radial flow at outlet
C. High speed with radial flow at outlet
D. High speed with mixed flow at outlet
Answer : D

40. Which type of the pump is different from others in the same group?
A. Screw pump
B. Gear pump
C. Cam and piston pump
D. Plunger pump
Answer : D

41. According to fan laws, for fans having constant wheel diameter, the pressure varies
A. Directly as fan speed
B. Square of fan speed
C. Cube of fan speed
D. Square root of fan speed
Answer : B

42. If the ratios of all the corresponding linear dimensions are equal, then the model and the prototype are said to have
A. Geometric similarity
B. Kinematic similarity
C. Dynamic similarity
D. None of these
Answer : A

43. Which of the following pump is suitable for small discharge and high heads?
A. Centrifugal pump
B. Axial flow pump
C. Mixed flow pump
D. Reciprocating pump
Answer : D

44. Saving of work done and power by fitting an air vessel to double acting reciprocating pump is of the order of
A. 39.2 %
B. 49.2 %
C. 68.8 %
D. 84.8 %
Answer : A

45. The hydraulic efficiency of an impulse turbine is maximum when velocity of wheel is _______ of the jet velocity,
A. One-fourth
B. One-half
C. Three-fourth
D. Double
Answer : B

46. Indicator diagram of a reciprocating pump is a graph between
A. Flow vs. swept volume
B. Pressure in cylinder vs. swept volume
C. Flow vs. speed
D. Pressure vs. speed
Answer : B

47. The speed ratio in case of Francis turbine varies from
A. 0.15 to 0.3
B. 0.4 to 0.5
C. 0.6 to 0.9
D. 1 to 1.5
Answer : C

48. For 450 m head of water, _________ shall be used.
A. Pelton wheel
B. Kaplan turbine
C. Francis turbine
D. None of these
Answer : A

49. A centrifugal pump will start delivering liquid only when the pressure rise in the impeller is equal to the
A. Kinetic head
B. Velocity head
C. Manometric head
D. Static head
Answer : C

50. For small discharge at high pressure, following pump is preferred
A. Centrifugal
B. Axial flow
C. Mixed flow
D. Reciprocating
Answer : D