Hydraulics & Fluid Machineries MCQ Solved Paper for IBPS SO

1. A Francis turbine is used when the available head of water is
A. 0 to 25 m
B. 25 m to 250 m
C. Above 250 m
D. None of these
Answer : B

2. Specific speed for reaction turbines ranges from
A. 0 to 4.5
B. 10 to 100
C. 80 to 200
D. 250 to 300
Answer : B

3. The hydraulic efficiency of an impulse turbine is the
A. Ratio of the actual power produced by the turbine to the energy actually supplied by the turbine
B. Ratio of the actual work available at the turbine to the energy imparted to the wheel
C. Ratio of the work done on the wheel to the energy of the jet
D. None of the above
Answer : C

4. The efficiency of a Pelton wheel working under constant head ________ with the increase in power.
A. Remain same
B. Increases
C. Decreases
D. None of these
Answer : B

5. Impulse turbine is generally fitted
A. At the level of tail race
B. Little above the tail race
C. Slightly below the tail race
D. About 2.5 m above the tail race to avoid cavitations.
Answer : B

6. The maximum number of jets, generally, employed in an impulse turbine without jet interference are
A. Two
B. Four
C. Six
D. Eight
Answer : C

7. If the ratios of all the corresponding linear dimensions are equal, then the model and the prototype are said to have
A. Geometric similarity
B. Kinematic similarity
C. Dynamic similarity
D. None of these
Answer : A

8. The power developed by a turbine is (where H = Head of water under which the turbine is working)
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : C

9. The hydraulic efficiency of an impulse turbine is maximum when velocity of wheel is _______ of the jet velocity,
A. One-fourth
B. One-half
C. Three-fourth
D. Double
Answer : B

10. Indicator diagram of a reciprocating pump is a graph between
A. Flow vs. swept volume
B. Pressure in cylinder vs. swept volume
C. Flow vs. speed
D. Pressure vs. speed
Answer : B

11. The runaway speed of a hydraulic turbine is the speed
A. At full load
B. At which there will be no damage to the runner
C. Corresponding to maximum overload permissible
D. At which the turbine will run freely without load
Answer : D

12. Axial flow pump is started with its delivery valve
A. Kept fully closed
B. Kept fully open
C. Irrespective of any position
D. Kept 50% open
Answer : B

13. The force exerted by a jet of water (in a direction normal to flow) impinging on a fixed plate inclined at an angle ? with the jet is
A. waV/2g × sin?
B. waV/g × sin?
C. waV²/2g × sin2?
D. waV²/g × sin?
Answer : C

14. The working of which of the following hydraulic units is based on Pascal's law?
A. Air lift pump
B. Jet pump
C. Hydraulic coupling
D. Hydraulic press
Answer : D

15. The specific speed of a centrifugal pump, delivering 750 litres of water per second against a head of 15 metres at 725 r.p.m., is
A. 24.8 r.p.m.
B. 48.2 r.p.m
C. 82.4 r.p.m.
D. 248 r.p.m
Answer : C

16. Geometric similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. Have identical forces
Answer : C

17. Puck up the wrong statement about centrifugal pump
A. Discharge a diameter
B. Head a speed²
C. Head a diameter
D. Power a speed?
Answer : A

18. Which of the following pump is preferred for flood control and irrigation applications?
A. Centrifugal pump
B. Axial flow pump
C. Mixed flow pump
D. Reciprocating pump
Answer : B

19. The specific speed of a hydraulic turbine depends upon
A. Speed and power developed
B. Discharge and power developed
C. Speed and head of water
D. Speed, power developed and head of water
Answer : D

20. In a reaction turbine, the draft tube is used
A. To run the turbine full
B. To prevent air to enter the turbine
C. To increase the head of water by an amount equal to the height of the runner outlet above the tail race
D. To transport water to downstream
Answer : C

21. In a Kaplan turbine runner, the numbers of blades are generally between
A. 2 to 4
B. 4 to 8
C. 8 to 16
D. 16 to 24
Answer : B

22. According to fan laws, at constant weight of air or gas, the speed, capacity and pressure vary
A. Directly as the air or gas density
B. Inversely as square root of density
C. Inversely as density
D. As square of density
Answer : C

23. The flow ratio of Francis turbine is defined as the ratio of the
A. Velocity of flow at inlet to the theoretical jet velocity
B. Theoretical velocity of jet to the velocity of flow at inlet
C. Velocity of runner at inlet to the velocity of flow at inlet
D. None of the above
Answer : A

24. The maximum efficiency of jet propulsion of a ship with inlet orifices at right angles to the direction of motion of ship, is
A. 40 %
B. 50 %
C. 60 %
D. 80 %
Answer : B

25. When a piping system is made up primarily of vertical lift and very little pipe friction, the pump characteristics should be
A. Horizontal
B. Nearly horizontal
C. Steep
D. First rise and then fall
Answer : C

26. The discharge of a double acting reciprocating pump is (where L = Length of stroke, A = Cross-sectional area of piston, and N = Speed of crank in r.p.m.)
A. L.A.N
B. 2 L.A.N
C. (L.A.N)/60
D. (2 L.A.N)/60
Answer : D

27. Which of the following statement is wrong?
A. The reaction turbines are used for low head and high discharge.
B. The angle of taper on draft tube is less than 8°.
C. An impulse turbine is generally fitted slightly above the tail race.
D. A Francis turbine is an impulse turbine.
Answer : D

28. Multistage centrifugal pumps are used to obtain
A. High discharge
B. High head
C. Pumping of viscous fluids
D. High head and high discharge
Answer : B

29. A Pelton wheel develops 1750 kW under a head of 100 metres while running at 200 r.p.m. and discharging 2500 litres of water per second. The unit power of the wheel is
A. 0.25 kW
B. 0.75 kW
C. 1.75 kW
D. 3.75 kW
Answer : C

30. The unit speed of the turbine runner is
A. N/?H
B. N/H
C. N/H^3/2
D. N/H²
Answer : A

31. The overall efficiency for a Pelton wheel lies between
A. 0.50 to 0.65
B. 0.65 to 0.75
C. 0.75 to 0.85
D. 0.85 to 0.90
Answer : D

32. The specific speed of a turbine is the speed of an imaginary turbine, identical with the given turbine, which
A. Delivers unit discharge under unit head
B. Delivers unit discharge under unit speed
C. Develops unit power under unit head
D. Develops unit power under unit speed
Answer : C

33. Which type of the pump is different from others in the same group?
A. Screw pump
B. Gear pump
C. Cam and piston pump
D. Plunger pump
Answer : D

34. The optimum value of vane exit angle for a centrifugal pump impeller is
A. 10-15°
B. 20-25°
C. 30-40°
D. 50-60°
Answer : B

35. If the net positive suction head (NPSH) requirement for the pump is not satisfied, then
A. No flow will take place
B. Cavitation will be formed
C. Efficiency will be low
D. Excessive power will be consumed
Answer : B

36. In an inward flow reaction turbine
A. The water flows parallel to the axis of the wheel
B. The water enters at the centre of the wheel and then flows towards the outer periphery of the wheel
C. The water enters the wheel at the outer periphery and then flows towards the centre of the wheel
D. The flow of water is partly radial and partly axial
Answer : C

37. A jet of water is striking at the centre of a curved vane moving with a uniform velocity in the direction of jet. For the maximum efficiency, the vane velocity is ________ of the jet velocity
A. One-half
B. One-third
C. Two-third
D. Three-fourth
Answer : B

38. A Pelton wheel develops 1750 kW under a head of 100 metres while running at 200 r.p.m. and discharging 2500 litres of water per second. The unit discharge of wheel is
A. 0.25 m³/s
B. 0.5 m³/s
C. 1.5 m³/s
D. 2.5 m³/s
Answer : A

39. The discharge through a reaction turbine ________ with the increase in unit speed.
A. Decreases
B. Increases
C. Remain same
D. None of these
Answer : A

40. The static head of a centrifugal pump is equal to the ________ of suction head and delivery head.
A. Product
B. Difference
C. Sum
D. None of these
Answer : C

41. When a piping system is made up primarily of friction head and very little of vertical lift, then pump characteristics should be
A. Horizontal
B. Nearly horizontal
C. Steep
D. First rise and then fall
Answer : B

42. A double overhung Pelton wheel has
A. Two jets
B. Two runners
C. Four jets
D. Four runners
Answer : B

43. The depth of the bucket for a Pelton wheel is generally ________ the diameter of jet.
A. Equal to
B. 1.2 times
C. 1.8 times
D. Double
Answer : B

44. According to fan laws, for fans having constant wheel diameter, the air or gas capacity varies
A. Directly as fan speed
B. Square of fan speed
C. Cube of fan speed
D. Square root of fan speed
Answer : A

45. The flow ratio in case of Francis turbine varies from
A. 0.15 to 0.3
B. 0.4 to 0.5
C. 0.6 to 0.9
D. 1 to 1.5
Answer : A

46. In a centrifugal pump casing, the flow of water leaving the
A. Radial
B. Axial
C. Centrifugal
D. Vortex
Answer : D

47. The speed of a turbine runner is
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : A

48. In a centrifugal pump casing, the flow of water leaving the impeller, is
A. Rectilinear flow
B. Radial flow
C. Free vortex motion
D. Forced vortex
Answer : C

49. Low specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. Any one of the above
Answer : C

50. High specific speed of a pump implies it is
A. Centrifugal pump
B. Mixed flow pump
C. Axial flow pump
D. Any one of the above
Answer : C