Hydraulics & Fluid Machineries MCQ Solved Paper for SBI Clerk

1. Indicator diagram of a reciprocating pump is a graph between
A. Flow vs. swept volume
B. Pressure in cylinder vs. swept volume
C. Flow vs. speed
D. Pressure vs. speed
Answer : B

2. The speed of a turbine runner is
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : A

3. A jet of water is striking at the centre of a curved vane moving with a uniform velocity in the direction of jet. For the maximum efficiency, the vane velocity is ________ of the jet velocity
A. One-half
B. One-third
C. Two-third
D. Three-fourth
Answer : B

4. The efficiency of a Pelton wheel working under constant head ________ with the increase in power.
A. Remain same
B. Increases
C. Decreases
D. None of these
Answer : B

5. Which of the following pump is successfully used for lifting water from deep wells?
A. Centrifugal pump
B. Reciprocating pump
C. Jet pump
D. Air lift pump
Answer : D

6. According to fan laws, at constant weight of air or gas, the speed, capacity and pressure vary
A. Directly as the air or gas density
B. Inversely as square root of density
C. Inversely as density
D. As square of density
Answer : C

7. Which of the following pump is successfully used for lifting water to the turbines?
A. Centrifugal pump
B. Reciprocating pump
C. Jet pump
D. Air lift pump
Answer : C

8. The flow rate in gear pump
A. Increases with increase in pressure
B. Decreases with increase in pressure
C. More or less remains constant with increase in pressure
D. Unpredictable
Answer : C

9. In a reciprocating pump, air vessels are used to
A. Smoothen the flow
B. Reduce suction head
C. Increase delivery head
D. Reduce acceleration head
Answer : D

10. The specific speed (Ns) of a centrifugal pump is given by
A. (N?Q)/H^2/3
B. (N?Q)/H^3/4
C. (N?Q)/H
D. (N?Q)/H^5/4
Answer : B

11. According to fan laws, for the fans having constant wheel diameters, the power demand varies
A. Directly as fan speed
B. Square of fan speed
C. Cube of fan speed
D. Square root of fan speed
Answer : C

12. The specific speed of a turbine is the speed of an imaginary turbine, identical with the given turbine, which
A. Delivers unit discharge under unit head
B. Delivers unit discharge under unit speed
C. Develops unit power under unit head
D. Develops unit power under unit speed
Answer : C

13. The force exerted by a jet of water (in a direction normal to flow) impinging on a fixed plate inclined at an angle ? with the jet is
A. waV/2g × sin?
B. waV/g × sin?
C. waV²/2g × sin2?
D. waV²/g × sin?
Answer : C

14. Geometric similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. Have identical forces
Answer : C

15. Saving of work done and power by fitting an air vessel to single acting reciprocating pump is of the order of
A. 39.2 %
B. 49.2 %
C. 68.8 %
D. 84.8 %
Answer : D

16. Hydraulic accumulator is used for
A. Accumulating oil
B. Supplying large quantities of oil for very short duration
C. Generally high pressures to operate hydraulic machines
D. Supplying energy when main supply fails
Answer : D

17. The ratio of actual work available at the turbine to the energy imparted to the wheel is known as ________ efficiency.
A. Hydraulic
B. Mechanical
C. Overall
D. None of these
Answer : B

18. Slip of a reciprocating pump is defined as the
A. Ratio of actual discharge to the theoretical discharge
B. Sum of actual discharge and the theoretical discharge
C. Difference of theoretical discharge and the actual discharge
D. Product of theoretical discharge and the actual discharge
Answer : C

19. Which place in hydraulic turbine is most susceptible for cavitations?
A. Inlet of draft rube
B. Blade inlet
C. Guide blade
D. Penstock
Answer : A

20. Mechanical efficiency of a centrifugal pump is the ratio of
A. Energy available at the impeller to the energy supplied to the pump by the prime mover
B. Actual workdone by the pump to the energy supplied to the pump by the prime mover
C. Energy supplied to the pump to the energy available at the impeller
D. Manometric head to the energy supplied by the impeller per kN of water
Answer : A

21. Low specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. Any one of the above
Answer : C

22. Centrifugal pump is started with its delivery valve
A. Kept fully closed
B. Kept fully open
C. Irrespective of any position
D. Kept 50% open
Answer : A

23. Guide angle as per the aerofoil theory of Kaplan turbine blade design is defined as the angle between
A. Lift and resultant force
B. Drag and resultant force
C. Lift and tangential force
D. Lift and drag
Answer : A

24. The unit speed of the turbine runner is
A. N/?H
B. N/H
C. N/H^3/2
D. N/H²
Answer : A

25. Any change in load is adjusted by adjusting following parameter on turbine
A. Net head
B. Absolute velocity
C. Blade velocity
D. Flow
Answer : D

26. Specific speed for reaction turbines ranges from
A. 0 to 4.5
B. 10 to 100
C. 80 to 200
D. 250 to 300
Answer : B

27. For very high discharge at low pressure such as for flood control and irrigation applications, following type of pump is preferred
A. Centrifugal
B. Axial flow
C. Reciprocating
D. Mixed flow
Answer : B

28. Maximum impulse will be developed in hydraulic ram when
A. Waste valve closes suddenly
B. Supply pipe is long
C. Supply pipe is short
D. Ram chamber is large
Answer : A

29. A Pelton wheel working under a constant head and discharge, has maximum efficiency when the speed ratio is
A. 0.26
B. 0.36
C. 0.46
D. 0.56
Answer : C

30. The optimum value of vane exit angle for a centrifugal pump impeller is
A. 10-15°
B. 20-25°
C. 30-40°
D. 50-60°
Answer : B

31. In a Kaplan turbine runner, the numbers of blades are generally between
A. 2 to 4
B. 4 to 8
C. 8 to 16
D. 16 to 24
Answer : B

32. For small discharge at high pressure, following pump is preferred
A. Centrifugal
B. Axial flow
C. Mixed flow
D. Reciprocating
Answer : D

33. When a piping system is made up primarily of vertical lift and very little pipe friction, the pump characteristics should be
A. Horizontal
B. Nearly horizontal
C. Steep
D. First rise and then fall
Answer : C

34. The jet ratio is defined as the ratio of the
A. Diameter of jet to the diameter of Pelton wheel
B. Velocity of jet to the velocity of Pelton wheel
C. Diameter of Pelton wheel to the diameter of jet
D. Velocity of Pelton wheel to the velocity of jet
Answer : C

35. The water in a jet propelled boat is drawn through the openings facing the direction of motion of the boat. The efficiency of propulsion is given by
A. 2V/(v_r - v)
B. 2V/(v_r + v)
C. V/(v_r - v)
D. V/(v_r + v)
Answer : B

36. The specific speed of a centrifugal pump, delivering 750 litres of water per second against a head of 15 metres at 725 r.p.m., is
A. 24.8 r.p.m.
B. 48.2 r.p.m
C. 82.4 r.p.m.
D. 248 r.p.m
Answer : C

37. The efficiency of jet propulsion for a ship with inlet orifices at right angles to the direction of motion of ship is given by
A. [2(V_r - v) v]/ V_r²
B. 2(V_r + v) v]/ V_r²
C. [(V_r - v) v]/ V_r
D. [(V_r + v) v]/ V_r
Answer : A

38. By fitting an air vessel to the reciprocating pump, there is always a saving of work done and subsequently saving of power. This saving in case of a single acting reciprocating pump is
A. 39.2 %
B. 48.8 %
C. 84.8 %
D. 88.4 %
Answer : C

39. A turbine develops 10000 kW under a head of 25 metres at 135 r.p.m. Its specific speed is
A. 175.4 r.p.m.
B. 215.5 r.p.m.
C. 241.5 r.p.m.
D. 275.4 r.p.m
Answer : C

40. The Fourneyron turbine is _________ reaction turbine.
A. An axial flow
B. An inward flow
C. An outward flow
D. A mixed flow
Answer : C

41. According to fan laws, for fans having constant wheel diameter, the air or gas capacity varies
A. Directly as fan speed
B. Square of fan speed
C. Cube of fan speed
D. Square root of fan speed
Answer : A

42. In a centrifugal pump casing, the flow of water leaving the
A. Radial
B. Axial
C. Centrifugal
D. Vortex
Answer : D

43. By fitting an air vessel to the reciprocating pump, there is always a saving of work done and subsequently saving of power. The saving in case of a double acting reciprocating pump is
A. 39.2 %
B. 48.8 %
C. 84.8 %
D. 88.4 %
Answer : A

44. Which of the following is not an impulse turbine?
A. Girad turbine
B. Turgo turbine
C. Pelton wheel
D. Kaplan turbine
Answer : D

45. The cavitation in a hydraulic machine is mainly due to
A. Low velocity
B. High velocity
C. Low pressure
D. High pressure
Answer : C

46. Which of the following pump is preferred for flood control and irrigation applications?
A. Centrifugal pump
B. Axial flow pump
C. Mixed flow pump
D. Reciprocating pump
Answer : B

47. Which of the following statement is correct as regard to water wheels?
A. They have slow speeds
B. They are suitable even for low water heads
C. They give constant efficiency, even if the discharge is not constant
D. All of the above
Answer : D

48. A Pelton wheel develops 1750 kW under a head of 100 metres while running at 200 r.p.m. and discharging 2500 litres of water per second. The unit power of the wheel is
A. 0.25 kW
B. 0.75 kW
C. 1.75 kW
D. 3.75 kW
Answer : C

49. The discharge through a reaction turbine with increase in unit speed
A. Increases
B. Decreases
C. Remain unaffected
D. First increases and then decreases
Answer : B

50. According to fan laws, for fans having constant wheel diameter, the pressure varies
A. Directly as fan speed
B. Square of fan speed
C. Cube of fan speed
D. Square root of fan speed
Answer : B