Hydraulics & Fluid Machineries MCQ Solved Paper for SSC CGL

1. Which of the following is not an impulse turbine?
A. Girad turbine
B. Turgo turbine
C. Pelton wheel
D. Kaplan turbine
Answer : D

2. The flow rate in gear pump
A. Increases with increase in pressure
B. Decreases with increase in pressure
C. More or less remains constant with increase in pressure
D. Unpredictable
Answer : C

3. One horsepower is equal to
A. 102 watts
B. 75 watts
C. 550 watts
D. 735 watts
Answer : D

4. According to fan laws, at constant weight of air or gas, the speed, capacity and pressure vary
A. Directly as the air or gas density
B. Inversely as square root of density
C. Inversely as density
D. As square of density
Answer : C

5. Delivery head of a centrifugal pump is
A. Directly proportional to N
B. Inversely proportional to N
C. Directly proportional to N²
D. Inversely proportional to N²
Answer : C

6. The flow ratio of Francis turbine is defined as the ratio of the
A. Velocity of flow at inlet to the theoretical jet velocity
B. Theoretical velocity of jet to the velocity of flow at inlet
C. Velocity of runner at inlet to the velocity of flow at inlet
D. None of the above
Answer : A

7. Discharge of a centrifugal pump is (where N = Speed of the pump impeller)
A. Directly proportional to N
B. Inversely proportional to N
C. Directly proportional to N²
D. Inversely proportional to N²
Answer : A

8. The hydraulic efficiency of a reaction turbine, is the ratio of
A. Power produced by the turbine to the energy actually supplied by the turbine
B. Actual work available at the turbine to energy imparted to the wheel
C. Workdone on the wheel to the energy (or head of water) actually supplied to the turbine
D. None of the above
Answer : C

9. The specific speed of a centrifugal pump, delivering 750 litres of water per second against a head of 15 metres at 725 r.p.m., is
A. 24.8 r.p.m.
B. 48.2 r.p.m
C. 82.4 r.p.m.
D. 248 r.p.m
Answer : C

10. Head developed by a centrifugal pump is
A. Proportional to diameter of impeller
B. Proportional to speed of impeller
C. Proportional to diameter and speed of impeller
D. None of the above
Answer : C

11. Which of the following is not a reaction turbine?
A. Fourneyron turbine
B. Journal turbine
C. Thomson's turbine
D. Pelton wheel
Answer : D

12. A hydraulic accumulator normally consists of
A. Two cylinders, two rams and a storage device
B. A cylinder and a ram
C. Two coaxial rams and two cylinders
D. A cylinder, a piston, storage tank and control valve
Answer : B

13. Maximum impulse will be developed in hydraulic ram when
A. Waste valve closes suddenly
B. Supply pipe is long
C. Supply pipe is short
D. Ram chamber is large
Answer : A

14. The static head of a centrifugal pump is equal to the ________ of suction head and delivery head.
A. Product
B. Difference
C. Sum
D. None of these
Answer : C

15. Puck up the wrong statement about centrifugal pump
A. Discharge a diameter
B. Head a speed²
C. Head a diameter
D. Power a speed?
Answer : A

16. Axial flow pump is started with its delivery valve
A. Kept fully closed
B. Kept fully open
C. Irrespective of any position
D. Kept 50% open
Answer : B

17. If a pump is handling water and is discharging a certain flow Q at a constant total dynamic head requiring a definite B.H.P., the same pump when handling a liquid of specific gravity 0.75 and viscosity nearly same as of water would discharge
A. Same quantity of liquid
B. 0.75 Q
C. Q/0.75
D. 1.5 Q
Answer : A

18. In an outward flow reaction turbine
A. The water flows parallel to the axis of the wheel
B. The water enters at the centre of the wheel and then flows towards the outer periphery of the wheel
C. The water enters the wheel at the outer periphery and then flows towards the centre of the wheel
D. The flow of water is partly radial and partly axial
Answer : B

19. In a reciprocating pump, air vessels are used to
A. Smoothen the flow
B. Reduce suction head
C. Increase delivery head
D. Reduce acceleration head
Answer : D

20. The width of the bucket for a Pelton wheel is generally ________ the diameter of jet.
A. Double
B. Three times
C. Four times
D. Five times
Answer : D

21. In a centrifugal pump, the regulating valve is provided on the
A. Casing
B. Delivery pipe
C. Suction pipe
D. Impeller
Answer : B

22. Power required (in watts) to drive a centrifugal pump is (where H_m = Manometric head in metres, w = Specific weight in N/m³, Q = Discharge of the pump in m³/s, and ?_o = Overall efficiency of the pump)
A. (w H_m) / (Q × ?_o)
B. (w H_m Q) / ?_o
C. (w Q) / (H_m × ?_o)
D. (w Q ?_o) / H_m
Answer : B

23. Discharge of a centrifugal pump is
A. Directly proportional to diameter of its impeller
B. Inversely proportional to diameter of its impeller
C. Directly proportional to (diameter)² of its impeller
D. Inversely proportional to (diameter)² of its impeller
Answer : D

24. The angle of taper on draft tube is
A. Greater than 15°
B. Greater than 8°
C. Greater than 5°
D. Less than 8°
Answer : D

25. Medium specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. Any one of the above
Answer : B

26. Slip of a reciprocating pump is defined as the
A. Ratio of actual discharge to the theoretical discharge
B. Sum of actual discharge and the theoretical discharge
C. Difference of theoretical discharge and the actual discharge
D. Product of theoretical discharge and the actual discharge
Answer : C

27. Any change in load is adjusted by adjusting following parameter on turbine
A. Net head
B. Absolute velocity
C. Blade velocity
D. Flow
Answer : D

28. Dynamic similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. None of the above
Answer : D

29. A double overhung Pelton wheel has
A. Two jets
B. Two runners
C. Four jets
D. Four runners
Answer : B

30. Runaway speed of a hydraulic turbine is
A. Full load speed
B. The speed at which turbine runner will be damaged
C. The speed if the turbine runner is allowed to revolve freely without load and with the wicket gates wide open
D. The speed corresponding to maximum overload permissible
Answer : C

31. Geometric similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. Have identical forces
Answer : C

32. An impulse turbine is used for
A. Low head of water
B. High head of water
C. Medium head of water
D. High discharge
Answer : B

33. The force exerted by a jet of water (in a direction normal to flow) impinging on a fixed plate inclined at an angle ? with the jet is
A. waV/2g × sin?
B. waV/g × sin?
C. waV²/2g × sin2?
D. waV²/g × sin?
Answer : C

34. Low specific speed of a pump implies it is
A. Centrifugal pump
B. Mixed flow pump
C. Axial flow pump
D. None of the above
Answer : A

35. A centrifugal pump will start delivering liquid only when the pressure rise in the impeller is equal to the
A. Kinetic head
B. Velocity head
C. Manometric head
D. Static head
Answer : C

36. Centrifugal pump is started with its delivery valve
A. Kept fully closed
B. Kept fully open
C. Irrespective of any position
D. Kept 50% open
Answer : A

37. The cavitation in a hydraulic machine
A. Causes noise and vibration of various parts
B. Reduces the discharge of a turbine
C. Causes sudden drop in power output and efficiency
D. All of the above
Answer : D

38. The working of which of the following hydraulic units is based on Pascal's law?
A. Air lift pump
B. Jet pump
C. Hydraulic coupling
D. Hydraulic press
Answer : D

39. Reaction turbines are used for
A. Low head
B. High head
C. High head and low discharge
D. Low head and high discharge
Answer : D

40. The ratio of quantity of liquid discharged per second from the pump to the quantity of liquid passing per second through the impeller is known as
A. Manometric efficiency
B. Mechanical efficiency
C. Overall efficiency
D. Volumetric efficiency
Answer : D

41. The ratio of the normal force of jet of water on a plate inclined at an angle of 30° as compared to that when the plate is normal to jet, is
A. 1/?2
B. 1/2
C. 1
D. ?2
Answer : B

42. The speed ratio in case of Francis turbine varies from
A. 0.15 to 0.3
B. 0.4 to 0.5
C. 0.6 to 0.9
D. 1 to 1.5
Answer : C

43. The maximum hydraulic efficiency of an impulse turbine is (where ? = Angle of blade tip at outlet)
A. (1 + cos ?)/2
B. (1 - cos ?)/2
C. (1 + sin ?)/2
D. (1 - sin ?)/2
Answer : A

44. Which of the following turbine is preferred for 0 to 25 m head of water?
A. Pelton wheel
B. Kaplan turbine
C. Francis turbine
D. None of these
Answer : B

45. Indicator diagram of a reciprocating pump is a graph between
A. Flow vs. swept volume
B. Pressure in cylinder vs. swept volume
C. Flow vs. speed
D. Pressure vs. speed
Answer : B

46. The number of buckets on the periphery of a Pelton wheel is given by
A. (D/2d) + 5
B. (D/2d) + 10
C. (D/2d) + 15
D. (D/2d) + 20
Answer : C

47. The specific speed of a hydraulic turbine depends upon
A. Speed and power developed
B. Discharge and power developed
C. Speed and head of water
D. Speed, power developed and head of water
Answer : D

48. The water in a jet propelled boat is drawn through the openings facing the direction of motion of the boat. The efficiency of propulsion is given by
A. 2V/(v_r - v)
B. 2V/(v_r + v)
C. V/(v_r - v)
D. V/(v_r + v)
Answer : B

49. The overall efficiency of a reaction turbine is the ratio of
A. Power produced by the turbine to the energy actually supplied by the turbine
B. Actual work available at the turbine to the energy imparted to the wheel
C. Workdone on the wheel to the energy (or head of water) actually supplied to the turbine
D. None of the above
Answer : A

50. Head developed by a centrifugal pump depends on
A. Impeller diameter
B. Speed
C. Fluid density
D. Both (A) and (B) above
Answer : D