Hydraulics & Fluid Machineries MCQ Solved Paper for UPSC IES

1. According to fan laws, for fans having constant wheel diameter, the air or gas capacity varies
A. Directly as fan speed
B. Square of fan speed
C. Cube of fan speed
D. Square root of fan speed
Answer : A

2. The cavitation in a hydraulic machine is mainly due to
A. Low velocity
B. High velocity
C. Low pressure
D. High pressure
Answer : C

3. Power required (in watts) to drive a centrifugal pump is (where H_m = Manometric head in metres, w = Specific weight in N/m³, Q = Discharge of the pump in m³/s, and ?_o = Overall efficiency of the pump)
A. (w H_m) / (Q × ?_o)
B. (w H_m Q) / ?_o
C. (w Q) / (H_m × ?_o)
D. (w Q ?_o) / H_m
Answer : B

4. A Pelton wheel develops 1750 kW under a head of 100 metres while running at 200 r.p.m. and discharging 2500 litres of water per second. The unit power of the wheel is
A. 0.25 kW
B. 0.75 kW
C. 1.75 kW
D. 3.75 kW
Answer : C

5. The efficiency of a Pelton wheel working under constant head ________ with the increase in power.
A. Remain same
B. Increases
C. Decreases
D. None of these
Answer : B

6. The discharge of a double acting reciprocating pump is (where L = Length of stroke, A = Cross-sectional area of piston, and N = Speed of crank in r.p.m.)
A. L.A.N
B. 2 L.A.N
C. (L.A.N)/60
D. (2 L.A.N)/60
Answer : D

7. For centrifugal pump impeller, the maximum value of the vane exit angle is
A. 10° to 15°
B. 15° to 20°
C. 20° to 25°
D. 25° to 30°
Answer : C

8. Any change in load is adjusted by adjusting following parameter on turbine
A. Net head
B. Absolute velocity
C. Blade velocity
D. Flow
Answer : D

9. The ratio of actual work available at the turbine to the energy imparted to the wheel is known as ________ efficiency.
A. Hydraulic
B. Mechanical
C. Overall
D. None of these
Answer : B

10. The flow rate in gear pump
A. Increases with increase in pressure
B. Decreases with increase in pressure
C. More or less remains constant with increase in pressure
D. Unpredictable
Answer : C

11. Braking jet in an impulse turbine is used
A. To break the jet of water
B. To bring the runner to rest in a short time
C. To change the direction of runner
D. None of these
Answer : B

12. Which place in hydraulic turbine is most susceptible for cavitations?
A. Inlet of draft rube
B. Blade inlet
C. Guide blade
D. Penstock
Answer : A

13. Which of the following hydraulic unit is used for transmitting increased or decreased torque to the driven shaft?
A. Hydraulic ram
B. Hydraulic intensifier
C. Hydraulic torque converter
D. Hydraulic accumulator
Answer : C

14. Which of the following statement is wrong?
A. The reaction turbines are used for low head and high discharge.
B. The angle of taper on draft tube is less than 8°.
C. An impulse turbine is generally fitted slightly above the tail race.
D. A Francis turbine is an impulse turbine.
Answer : D

15. A Pelton wheel develops 1750 kW under a head of 100 metres while running at 200 r.p.m. and discharging 2500 litres of water per second. The unit speed of the wheel is
A. 10 r.p.m.
B. 20 r.p.m.
C. 40 r.p.m.
D. 80 r.p.m.
Answer : B

16. If a pump is handling water and is discharging a certain flow Q at a constant total dynamic head requiring a definite B.H.P., the same pump when handling a liquid of specific gravity 0.75 and viscosity nearly same as of water would discharge
A. Same quantity of liquid
B. 0.75 Q
C. Q/0.75
D. 1.5 Q
Answer : A

17. Which of the following pump is generally used to pump highly viscous fluid?
A. Centrifugal pump
B. Reciprocating pump
C. Air lift pump
D. Screw pump
Answer : D

18. According to fan laws, for fans having constant wheel diameter, the pressure varies
A. Directly as fan speed
B. Square of fan speed
C. Cube of fan speed
D. Square root of fan speed
Answer : B

19. Dynamic similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. None of the above
Answer : D

20. The maximum efficiency of jet propulsion of a ship with inlet orifices at right angles to the direction of motion of ship, is
A. 40 %
B. 50 %
C. 60 %
D. 80 %
Answer : B

21. The specific speed (Ns) of a centrifugal pump is given by
A. (N?Q)/H^2/3
B. (N?Q)/H^3/4
C. (N?Q)/H
D. (N?Q)/H^5/4
Answer : B

22. Low specific speed of a pump implies it is
A. Centrifugal pump
B. Mixed flow pump
C. Axial flow pump
D. None of the above
Answer : A

23. The specific speed from 160 to 500 r.p.m. of a centrifugal pump indicates that the pump is
A. Slow speed with radial flow at outlet
B. Medium speed with radial flow at outlet
C. High speed with radial flow at outlet
D. High speed with axial flow at outlet
Answer : D

24. The flow ratio of Francis turbine is defined as the ratio of the
A. Velocity of flow at inlet to the theoretical jet velocity
B. Theoretical velocity of jet to the velocity of flow at inlet
C. Velocity of runner at inlet to the velocity of flow at inlet
D. None of the above
Answer : A

25. When a piping system is made up primarily of friction head and very little of vertical lift, then pump characteristics should be
A. Horizontal
B. Nearly horizontal
C. Steep
D. First rise and then fall
Answer : B

26. The relation between hydraulic efficiency (?_h), mechanical efficiency (?_m) and overall efficiency (?_o) is
A. ?_h = ?_o × ?_m
B. ?_m = ?_m × ?_h
C. ?_o = ?_h × ?_m
D. None of these
Answer : C

27. Mechanical efficiency of a centrifugal pump is the ratio of
A. Energy available at the impeller to the energy supplied to the pump by the prime mover
B. Actual workdone by the pump to the energy supplied to the pump by the prime mover
C. Energy supplied to the pump to the energy available at the impeller
D. Manometric head to the energy supplied by the impeller per kN of water
Answer : A

28. Air vessels in reciprocating pump are used to
A. Smoothen flow
B. Reduce acceleration to minimum
C. Increase pump efficiency
D. Save pump from cavitations
Answer : B

29. In a reciprocating pump, air vessels are used to
A. Smoothen the flow
B. Reduce suction head
C. Increase delivery head
D. Reduce acceleration head
Answer : D

30. Axial flow pump is started with its delivery valve
A. Kept fully closed
B. Kept fully open
C. Irrespective of any position
D. Kept 50% open
Answer : B

31. The speed ratio in case of Francis turbine varies from
A. 0.15 to 0.3
B. 0.4 to 0.5
C. 0.6 to 0.9
D. 1 to 1.5
Answer : C

32. Francis, Kaplan and propeller turbines fall under the category of
A. Impulse turbines
B. Reaction turbines
C. Axial flow turbines
D. Mixed flow turbines
Answer : B

33. Multistage centrifugal pumps are used to obtain
A. High discharge
B. High head
C. Pumping of viscous fluids
D. High head and high discharge
Answer : B

34. A Pelton wheel working under a constant head and discharge, has maximum efficiency when the speed ratio is
A. 0.26
B. 0.36
C. 0.46
D. 0.56
Answer : C

35. Which of the following pump is successfully used for lifting water from deep wells?
A. Centrifugal pump
B. Reciprocating pump
C. Jet pump
D. Air lift pump
Answer : D

36. A turbine pump is basically a centrifugal pump equipped additionally with
A. Adjustable blades
B. Backward curved blades
C. Vaned diffusion casing
D. Inlet guide blades
Answer : C

37. Which of the following turbine is preferred for a specific speed of 60 to 300 r.p.m.?
A. Pelton wheel
B. Francis turbine
C. Kaplan turbine
D. None of these
Answer : B

38. The cavitation in a hydraulic machine
A. Causes noise and vibration of various parts
B. Reduces the discharge of a turbine
C. Causes sudden drop in power output and efficiency
D. All of the above
Answer : D

39. The overall efficiency of a reaction turbine is the ratio of
A. Power produced by the turbine to the energy actually supplied by the turbine
B. Actual work available at the turbine to the energy imparted to the wheel
C. Workdone on the wheel to the energy (or head of water) actually supplied to the turbine
D. None of the above
Answer : A

40. The hydraulic efficiency of a reaction turbine, is the ratio of
A. Power produced by the turbine to the energy actually supplied by the turbine
B. Actual work available at the turbine to energy imparted to the wheel
C. Workdone on the wheel to the energy (or head of water) actually supplied to the turbine
D. None of the above
Answer : C

41. The maximum hydraulic efficiency of an impulse turbine is (where ? = Angle of blade tip at outlet)
A. (1 + cos ?)/2
B. (1 - cos ?)/2
C. (1 + sin ?)/2
D. (1 - sin ?)/2
Answer : A

42. The unit discharge through the turbine is
A. Q/?H
B. Q/H
C. Q/H^3/2
D. Q/H²
Answer : A

43. If a pump is handling water and is discharging a certain flow Q at a constant total dynamic head requiring a definite B.H.P., the same pump when handling a liquid of specific gravity 0.75 and viscosity nearly same as of water, the horse power required will be
A. Same
B. 0.75 B.H.P.
C. B.H.P./0.75
D. 1.5 B.H.P.
Answer : B

44. Slip of a reciprocating pump is defined as the
A. Ratio of actual discharge to the theoretical discharge
B. Sum of actual discharge and the theoretical discharge
C. Difference of theoretical discharge and the actual discharge
D. Product of theoretical discharge and the actual discharge
Answer : C

45. The centrifugal pump preferred for a specific speed between 80 to 160 r.p.m. is
A. Slow speed with radial flow at outlet
B. Medium speed with radial flow at outlet
C. High speed with radial flow at outlet
D. High speed with mixed flow at outlet
Answer : D

46. Low specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. Any one of the above
Answer : C

47. In a reaction turbine, the draft tube is used
A. To run the turbine full
B. To prevent air to enter the turbine
C. To increase the head of water by an amount equal to the height of the runner outlet above the tail race
D. To transport water to downstream
Answer : C

48. The water in a jet propelled boat is drawn through the openings facing the direction of motion of the boat. The efficiency of propulsion is given by
A. 2V/(v_r - v)
B. 2V/(v_r + v)
C. V/(v_r - v)
D. V/(v_r + v)
Answer : B

49. The jet ratio is defined as the ratio of the
A. Diameter of jet to the diameter of Pelton wheel
B. Velocity of jet to the velocity of Pelton wheel
C. Diameter of Pelton wheel to the diameter of jet
D. Velocity of Pelton wheel to the velocity of jet
Answer : C

50. Head developed by a centrifugal pump is
A. Proportional to diameter of impeller
B. Proportional to speed of impeller
C. Proportional to diameter and speed of impeller
D. None of the above
Answer : C