Hydraulics & Fluid Machineries MCQ Solved Paper for SSC GD

1. High specific speed of a pump implies it is
A. Centrifugal pump
B. Mixed flow pump
C. Axial flow pump
D. Any one of the above
Answer : C

2. Which of the following turbine is preferred for 0 to 25 m head of water?
A. Pelton wheel
B. Kaplan turbine
C. Francis turbine
D. None of these
Answer : B

3. The power developed by a turbine is (where H = Head of water under which the turbine is working)
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : C

4. Saving of work done and power by fitting an air vessel to double acting reciprocating pump is of the order of
A. 39.2 %
B. 49.2 %
C. 68.8 %
D. 84.8 %
Answer : A

5. Slip of a reciprocating pump is negative, when
A. Suction pipe is short and pump is running at low speeds
B. Delivery pipe is long and pump is running at high speeds
C. Suction pipe is short and delivery pipe is long and the pump is running at low speeds
D. Suction pipe is long and delivery pipe is short and the pump is running at high speeds
Answer : D

6. According to fan laws, at constant pressure, the speed capacity and power vary
A. Directly as the air or gas density
B. Inversely as square root of density
C. Inversely as density
D. As square of density
Answer : B

7. The unit power developed by a turbine is (where P = Power developed by the turbine under a head of water (H).
A. P/ ?H
B. P/ H
C. P/ H^3/2
D. P/ H²
Answer : C

8. Medium specific speed of a pump implies it is
A. Centrifugal pump
B. Mixed flow pump
C. Axial flow pump
D. Any one of the above
Answer : B

9. The mechanical efficiency of an impulse turbine is
A. Ratio of the actual power produced by the turbine to the energy actually supplied by the turbine
B. Ratio of the actual work available at the turbine to the energy imparted to the wheel
C. Ratio of the Work done on the wheel to the energy of the jet
D. None of the above
Answer : B

10. In centrifugal pumps, maximum efficiency is obtained when the blades are
A. Straight
B. Bent forward
C. Bent backward
D. Radial
Answer : C

11. Guide angle as per the aerofoil theory of Kaplan turbine blade design is defined as the angle between
A. Lift and resultant force
B. Drag and resultant force
C. Lift and tangential force
D. Lift and drag
Answer : A

12. In order to avoid cavitation in centrifugal pumps
A. The suction pressure should be high
B. The delivery pressure should be high
C. The suction pressure should be low
D. The delivery pressure should be low
Answer : A

13. If the ratios of all the corresponding linear dimensions are equal, then the model and the prototype are said to have
A. Geometric similarity
B. Kinematic similarity
C. Dynamic similarity
D. None of these
Answer : A

14. If a pump is handling water and is discharging a certain flow Q at a constant total dynamic head requiring a definite B.H.P., the same pump when handling a liquid of specific gravity 0.75 and viscosity nearly same as of water, the horse power required will be
A. Same
B. 0.75 B.H.P.
C. B.H.P./0.75
D. 1.5 B.H.P.
Answer : B

15. Mechanical efficiency of a centrifugal pump is the ratio of
A. Energy available at the impeller to the energy supplied to the pump by the prime mover
B. Actual workdone by the pump to the energy supplied to the pump by the prime mover
C. Energy supplied to the pump to the energy available at the impeller
D. Manometric head to the energy supplied by the impeller per kN of water
Answer : A

16. A Pelton wheel develops 1750 kW under a head of 100 metres while running at 200 r.p.m. and discharging 2500 litres of water per second. The unit discharge of wheel is
A. 0.25 m³/s
B. 0.5 m³/s
C. 1.5 m³/s
D. 2.5 m³/s
Answer : A

17. The specific speed of a turbine is given by the equation
A. N?P / H^3/2
B. N?P / H²
C. N?P / H^5/4
D. N?P / H³
Answer : C

18. A turbine pump is basically a centrifugal pump equipped additionally with
A. Adjustable blades
B. Backward curved blades
C. Vaned diffusion casing
D. Inlet guide blades
Answer : C

19. Multistage centrifugal pumps are used to obtain
A. High discharge
B. High head
C. Pumping of viscous fluids
D. High head and high discharge
Answer : B

20. Head developed by a centrifugal pump depends on
A. Impeller diameter
B. Speed
C. Fluid density
D. Both (A) and (B) above
Answer : D

21. Centrifugal pump is started with its delivery valve
A. Kept fully closed
B. Kept fully open
C. Irrespective of any position
D. Kept 50% open
Answer : A

22. According to fan laws, for fans having constant wheel diameter, the air or gas capacity varies
A. Directly as fan speed
B. Square of fan speed
C. Cube of fan speed
D. Square root of fan speed
Answer : A

23. Which of the following pump is successfully used for lifting water to the turbines?
A. Centrifugal pump
B. Reciprocating pump
C. Jet pump
D. Air lift pump
Answer : C

24. For 450 m head of water, _________ shall be used.
A. Pelton wheel
B. Kaplan turbine
C. Francis turbine
D. None of these
Answer : A

25. Power required to drive a centrifugal pump is directly proportional to ________ of its impeller.
A. Diameter
B. Square of diameter
C. Cube of diameter
D. Fourth power of diameter
Answer : D

26. For small discharge at high pressure, following pump is preferred
A. Centrifugal
B. Axial flow
C. Mixed flow
D. Reciprocating
Answer : D

27. The ratio of actual work available at the turbine to the energy imparted to the wheel is known as ________ efficiency.
A. Hydraulic
B. Mechanical
C. Overall
D. None of these
Answer : B

28. The discharge of a double acting reciprocating pump is (where L = Length of stroke, A = Cross-sectional area of piston, and N = Speed of crank in r.p.m.)
A. L.A.N
B. 2 L.A.N
C. (L.A.N)/60
D. (2 L.A.N)/60
Answer : D

29. The maximum number of jets generally employed in impulse turbine without jet interference is
A. 4
B. 6
C. 8
D. 12
Answer : B

30. When a piping system is made up primarily of vertical lift and very little pipe friction, the pump characteristics should be
A. Horizontal
B. Nearly horizontal
C. Steep
D. First rise and then fall
Answer : C

31. The number of buckets on the periphery of a Pelton wheel is given by
A. (D/2d) + 5
B. (D/2d) + 10
C. (D/2d) + 15
D. (D/2d) + 20
Answer : C

32. Casting of a centrifugal pump is designed so as to minimize
A. Friction loss
B. Cavitations
C. Static head
D. Loss of kinetic energy
Answer : D

33. Reciprocating pumps are no more to be seen in industrial applications (in comparison to centrifugal pumps) because of
A. High initial and maintenance cost
B. Lower discharge
C. Lower speed of operation
D. Necessity of air vessel
Answer : A

34. Impulse turbine is generally fitted
A. At the level of tail race
B. Little above the tail race
C. Slightly below the tail race
D. About 2.5 m above the tail race to avoid cavitations.
Answer : B

35. In a reaction turbine, the draft tube is used
A. To run the turbine full
B. To prevent air to enter the turbine
C. To increase the head of water by an amount equal to the height of the runner outlet above the tail race
D. To transport water to downstream
Answer : C

36. Which of the following pump is generally used to pump highly viscous fluid?
A. Centrifugal pump
B. Reciprocating pump
C. Air lift pump
D. Screw pump
Answer : D

37. Runaway speed of a hydraulic turbine is
A. Full load speed
B. The speed at which turbine runner will be damaged
C. The speed if the turbine runner is allowed to revolve freely without load and with the wicket gates wide open
D. The speed corresponding to maximum overload permissible
Answer : C

38. The efficiency of a Pelton wheel working under constant head ________ with the increase in power.
A. Remain same
B. Increases
C. Decreases
D. None of these
Answer : B

39. By fitting an air vessel to the reciprocating pump, there is always a saving of work done and subsequently saving of power. The saving in case of a double acting reciprocating pump is
A. 39.2 %
B. 48.8 %
C. 84.8 %
D. 88.4 %
Answer : A

40. The depth of the bucket for a Pelton wheel is generally ________ the diameter of jet.
A. Equal to
B. 1.2 times
C. 1.8 times
D. Double
Answer : B

41. For starting an axial flow pump, its delivery valve should be
A. Closed
B. Open
C. Depends on starting condition and flow desired
D. Could be either open or closed
Answer : B

42. The maximum number of jets, generally, employed in an impulse turbine without jet interference are
A. Two
B. Four
C. Six
D. Eight
Answer : C

43. In a Francis turbine runner, the numbers of blades are generally between
A. 2 to 4
B. 4 to 8
C. 8 to 16
D. 16 to 24
Answer : D

44. An impulse turbine is used for
A. Low head of water
B. High head of water
C. Medium head of water
D. High discharge
Answer : B

45. Which place in hydraulic turbine is most susceptible for cavitations?
A. Inlet of draft rube
B. Blade inlet
C. Guide blade
D. Penstock
Answer : A

46. The hydraulic efficiency of a reaction turbine, is the ratio of
A. Power produced by the turbine to the energy actually supplied by the turbine
B. Actual work available at the turbine to energy imparted to the wheel
C. Workdone on the wheel to the energy (or head of water) actually supplied to the turbine
D. None of the above
Answer : C

47. The relation between hydraulic efficiency (?_h), mechanical efficiency (?_m) and overall efficiency (?_o) is
A. ?_h = ?_o × ?_m
B. ?_m = ?_m × ?_h
C. ?_o = ?_h × ?_m
D. None of these
Answer : C

48. The unit discharge through the turbine is
A. Q/?H
B. Q/H
C. Q/H^3/2
D. Q/H²
Answer : A

49. Delivery head of a centrifugal pump is
A. Directly proportional to N
B. Inversely proportional to N
C. Directly proportional to N²
D. Inversely proportional to N²
Answer : C

50. If a pump is handling water and is discharging a certain flow Q at a constant total dynamic head requiring a definite B.H.P., the same pump when handling a liquid of specific gravity 0.75 and viscosity nearly same as of water would discharge
A. Same quantity of liquid
B. 0.75 Q
C. Q/0.75
D. 1.5 Q
Answer : A