SSC Scientific Assistant - Hydraulics & Fluid Machineries 1000+ MCQ [Solved] PDF Download

1. The Fourneyron turbine is _________ reaction turbine.
A. An axial flow
B. An inward flow
C. An outward flow
D. A mixed flow
Answer : C

2. Slip of a reciprocating pump is negative, when
A. Suction pipe is short and pump is running at low speeds
B. Delivery pipe is long and pump is running at high speeds
C. Suction pipe is short and delivery pipe is long and the pump is running at low speeds
D. Suction pipe is long and delivery pipe is short and the pump is running at high speeds
Answer : D

3. Casting of a centrifugal pump is designed so as to minimize
A. Friction loss
B. Cavitations
C. Static head
D. Loss of kinetic energy
Answer : D

4. Mechanical efficiency of a centrifugal pump is the ratio of
A. Energy available at the impeller to the energy supplied to the pump by the prime mover
B. Actual workdone by the pump to the energy supplied to the pump by the prime mover
C. Energy supplied to the pump to the energy available at the impeller
D. Manometric head to the energy supplied by the impeller per kN of water
Answer : A

5. The optimum value of vane exit angle for a centrifugal pump impeller is
A. 10-15°
B. 20-25°
C. 30-40°
D. 50-60°
Answer : B

6. If the net positive suction head (NPSH) requirement for the pump is not satisfied, then
A. No flow will take place
B. Cavitation will be formed
C. Efficiency will be low
D. Excessive power will be consumed
Answer : B

7. A hydraulic press is a device used
A. To store pressure energy which may be supplied to a machine later on
B. To increase the intensity of pressure of water by means of energy available from a large quantity of water at a low pressure
C. To lift larger load by the application of a comparatively much smaller force
D. All of the above
Answer : C

8. In order to avoid cavitation in centrifugal pumps
A. The suction pressure should be high
B. The delivery pressure should be high
C. The suction pressure should be low
D. The delivery pressure should be low
Answer : A

9. Which type of the pump is different from others in the same group?
A. Screw pump
B. Gear pump
C. Cam and piston pump
D. Plunger pump
Answer : D

10. Which place in hydraulic turbine is most susceptible for cavitations?
A. Inlet of draft rube
B. Blade inlet
C. Guide blade
D. Penstock
Answer : A

11. Low specific speed of a pump implies it is
A. Centrifugal pump
B. Mixed flow pump
C. Axial flow pump
D. None of the above
Answer : A

12. By fitting an air vessel to the reciprocating pump, there is always a saving of work done and subsequently saving of power. This saving in case of a single acting reciprocating pump is
A. 39.2 %
B. 48.8 %
C. 84.8 %
D. 88.4 %
Answer : C

13. Hydraulic accumulator is used for
A. Accumulating oil
B. Supplying large quantities of oil for very short duration
C. Generally high pressures to operate hydraulic machines
D. Supplying energy when main supply fails
Answer : D

14. For small discharge at high pressure, following pump is preferred
A. Centrifugal
B. Axial flow
C. Mixed flow
D. Reciprocating
Answer : D

15. Kinematic similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. Have identical forces
Answer : A

16. The specific speed of turbine is defined as the speed of a unit
A. Of such a size that it delivers unit discharge at unit head
B. Of such a size that it delivers unit discharge at unit power
C. Of such a size that it requires unit power per unit head
D. Of such a size that it produces unit horse power with unit head
Answer : D

17. A turbine is required to develop 1500 kW at 300 r.p.m. under a head of 150 m. Which of the following turbine should be used?
A. Pelton wheel with one nozzle
B. Pelton wheel with two or more nozzles
C. Kaplan turbine
D. Francis turbine
Answer : A

18. In axial flow fans and turbines, fluid enters and leaves as follows
A. Radially, axially
B. Axially, radially
C. Axially, axially
D. Radially, radially
Answer : C

19. The mechanical efficiency of an impulse turbine is
A. Ratio of the actual power produced by the turbine to the energy actually supplied by the turbine
B. Ratio of the actual work available at the turbine to the energy imparted to the wheel
C. Ratio of the Work done on the wheel to the energy of the jet
D. None of the above
Answer : B

20. In an inward flow reaction turbine
A. The water flows parallel to the axis of the wheel
B. The water enters at the centre of the wheel and then flows towards the outer periphery of the wheel
C. The water enters the wheel at the outer periphery and then flows towards the centre of the wheel
D. The flow of water is partly radial and partly axial
Answer : C

21. The efficiency of jet propulsion for a ship with inlet orifices at right angles to the direction of motion of ship is given by
A. [2(V_r - v) v]/ V_r²
B. 2(V_r + v) v]/ V_r²
C. [(V_r - v) v]/ V_r
D. [(V_r + v) v]/ V_r
Answer : A

22. Discharge (Q) of a centrifugal pump is given by (where D = Diameter of impeller at inlet, b = Width of impeller at inlet, and Vf = Velocity of flow at inlet)
A. Q = ?.D.Vf
B. Q = ?.b.Vf
C. Q = ?.D.bf.V
D. Q = D.b.Vf
Answer : C

23. The cavitation in reaction turbines is avoided, to a great extent by
A. Installing the turbine below the tail race level
B. Using stainless steel runner of the turbine
C. Providing highly polished blades to the runner
D. All of the above
Answer : D

24. Reaction turbines are used for
A. Low head
B. High head
C. High head and low discharge
D. Low head and high discharge
Answer : D

25. Power required to drive a centrifugal pump is directly proportional to ________ of its impeller.
A. Diameter
B. Square of diameter
C. Cube of diameter
D. Fourth power of diameter
Answer : D

26. Discharge of a centrifugal pump is (where N = Speed of the pump impeller)
A. Directly proportional to N
B. Inversely proportional to N
C. Directly proportional to N²
D. Inversely proportional to N²
Answer : A

27. The depth of the bucket for a Pelton wheel is generally ________ the diameter of jet.
A. Equal to
B. 1.2 times
C. 1.8 times
D. Double
Answer : B

28. A hydraulic intensifier normally consists of
A. Two cylinders, two rams and a storage device
B. A cylinder and a ram
C. Two coaxial rams and two cylinders
D. A cylinder, a piston, storage tank and control valve
Answer : C

29. The jet ratio is defined as the ratio of the
A. Diameter of jet to the diameter of Pelton wheel
B. Velocity of jet to the velocity of Pelton wheel
C. Diameter of Pelton wheel to the diameter of jet
D. Velocity of Pelton wheel to the velocity of jet
Answer : C

30. The width of the bucket for a Pelton wheel is generally ________ the diameter of jet.
A. Double
B. Three times
C. Four times
D. Five times
Answer : D

31. A hydraulic accumulator normally consists of
A. Two cylinders, two rams and a storage device
B. A cylinder and a ram
C. Two coaxial rams and two cylinders
D. A cylinder, a piston, storage tank and control valve
Answer : B

32. The discharge through a turbine is
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : A

33. A ship with jet propulsion draws water through inlet orifices at right angles to the direction of its motion. The propelling force of the jet is (where a = Area of the jet, Vr = Relative velocity of the jet and ship = V + v, v = Velocity of the ship, and V = Velocity of the jet issuing from the ship)
A. waVr /g × (Vr + v)
B. waVr /g × (Vr - v)
C. waVr /g × (Vr + v)²
D. waVr /g × (Vr - v)²
Answer : B

34. By fitting an air vessel to the reciprocating pump, there is always a saving of work done and subsequently saving of power. The saving in case of a double acting reciprocating pump is
A. 39.2 %
B. 48.8 %
C. 84.8 %
D. 88.4 %
Answer : A

35. Any change in load is adjusted by adjusting following parameter on turbine
A. Net head
B. Absolute velocity
C. Blade velocity
D. Flow
Answer : D

36. Power required (in watts) to drive a centrifugal pump is (where H_m = Manometric head in metres, w = Specific weight in N/m³, Q = Discharge of the pump in m³/s, and ?_o = Overall efficiency of the pump)
A. (w H_m) / (Q × ?_o)
B. (w H_m Q) / ?_o
C. (w Q) / (H_m × ?_o)
D. (w Q ?_o) / H_m
Answer : B

37. A Pelton wheel is
A. Tangential flow impulse turbine
B. Inward flow impulse turbine
C. Outward flow impulse turbine
D. Inward flow reaction turbine
Answer : A

38. The unit speed of the turbine runner is
A. N/?H
B. N/H
C. N/H^3/2
D. N/H²
Answer : A

39. The specific speed (Ns) of a centrifugal pump is given by
A. (N?Q)/H^2/3
B. (N?Q)/H^3/4
C. (N?Q)/H
D. (N?Q)/H^5/4
Answer : B

40. For centrifugal pump impeller, the maximum value of the vane exit angle is
A. 10° to 15°
B. 15° to 20°
C. 20° to 25°
D. 25° to 30°
Answer : C

41. The type of centrifugal pump preferred for a specific speed of 20 r.p.m. is
A. Slow speed pump with radial flow at outlet
B. Medium speed pump with radial flow at outlet
C. High speed pump with radial flow at outlet
D. High speed pump with axial flow at outlet
Answer : A

42. Which of the following statement is correct as regard to water wheels?
A. They have slow speeds
B. They are suitable even for low water heads
C. They give constant efficiency, even if the discharge is not constant
D. All of the above
Answer : D

43. In a single casing, multistage pump running at constant speed, the capacity rating is to be slightly lowered. It can be done by
A. Designing new impeller
B. Trimming the impeller size to the required size by machining
C. Not possible
D. Some other alterations in the impeller
Answer : B

44. Saving of work done and power by fitting an air vessel to double acting reciprocating pump is of the order of
A. 39.2 %
B. 49.2 %
C. 68.8 %
D. 84.8 %
Answer : A

45. Motion of a liquid in a volute casing of a centrifugal pump is an example of
A. Rotational flow
B. Radial
C. Forced spiral vortex flow
D. Spiral vortex flow
Answer : D

46. The hydraulic efficiency of an impulse turbine is the
A. Ratio of the actual power produced by the turbine to the energy actually supplied by the turbine
B. Ratio of the actual work available at the turbine to the energy imparted to the wheel
C. Ratio of the work done on the wheel to the energy of the jet
D. None of the above
Answer : C

47. Which of the following is not a reaction turbine?
A. Fourneyron turbine
B. Journal turbine
C. Thomson's turbine
D. Pelton wheel
Answer : D

48. The power developed by a turbine is (where H = Head of water under which the turbine is working)
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : C

49. A hydraulic coupling belongs to the category of
A. Power absorbing machines
B. Power developing machines
C. Energy transfer machines
D. Energy generating machines
Answer : C

50. If a pump is handling water and is discharging a certain flow Q at a constant total dynamic head requiring a definite B.H.P., the same pump when handling a liquid of specific gravity 0.75 and viscosity nearly same as of water, the horse power required will be
A. Same
B. 0.75 B.H.P.
C. B.H.P./0.75
D. 1.5 B.H.P.
Answer : B