Compression force in two end posts, the pin of a rocker bearing in a bridge is designed for
Bearing and shear
Bending and shear
Bearing and bending
Bearing, shear and bending
Correct Answer :
D. Bearing, shear and bending
Related Questions
If fbt and fc are the co-existent bending tensile stress and shear stress in a member, the equivalent stress fc is
√(fbt² + fc²)
√(fbt² + ½fc²)
√(fbt² + 3fc²)
√(fbt² - 3fc²)
For a compression member with double angle section, which of the following section will give larger value of minimum radius of gyration?
Equal angles back to back
Unequal legged angles with long legs back to back
Unequal legged angles with short legs back to back
Both (B) and (C)
The strength of ISA 125 = 75 × 10 mm used as a tie member with its longer leg connected at the ends by 27 mm diameter rivets, is
26,000 kg
26,025 kg
26,050 kg
26,075 kg
A single angle in tension is connected by one leg only. If the areas of connecting and outstanding legs are respectively a and b, net effective area of the angle, is
a - [b/{1 + 0.35 (b/a)}]
a + [b/{1 + 0.35 (b/a)}]
a - [b/{1 + 0.2 (b/a)}]
a + [b/{1 + 0.2 (b/a)}]
Diameter of a rivet hole is made larger than the diameter of the rivet by
1.0 mm for rivet diameter upto 12 mm
1.5 mm for rivet diameter exceeding 25 mm
2.0 mm for rivet diameter over 25 mm
None of these
If the moment of inertia of a section about its axis is I and its effective sectional area is A, its radius of gyration r about the axis, is
r = I/A
r = √(I/A)
r = (I/A)
r = √(A/I)
If a pair of angles placed back to back in tension are connected by one leg of each angle, the net effective area of the section, is
a - [b/{1 + 0.35 (b/a)}]
a + [b/{1 + 0.35 (b/a)}]
a - [b/{1 + 0.2 (b/a)}]
a + [b/{1 + 0.2 (b/a)}]
In a built up section carrying a tensile force, the flanges of two channels are turned outward
To simplify the transverse connections
To minimise lacing
To have greater lateral rigidity
All the above
Under a concentrated load, bearing stress fb in a beam is given by (where b is the length of the bearing plate and h is the depth of the root of the fillet).
fb = W/(b + h√3)tw
fb = W/(b + 2h√3)tw
fb = W/(b + 2h√2)tw
fb = W/(b + h√2)tw
The external wind pressure acting on a roof depends on
Degree of permeability of roof
Slope of roof
Both (A) and (B)
None of the above
Maximum permissible slenderness ratio of a member normally acting as a tie in a roof truss, is
180
200
250
350
A fillet weld may be termed as
Mitre weld
Concave weld
Convex weld
All the above
The connection of intermediate vertical stiffeners to the web, not subjected to external loads, shall be designed for a minimum shear force (kN/m) of
75 t²/h
125 t3/h²
125 t²/h
175 t²/h Where, t = the web thickness in mm and h = the outstand of stiffener in mm
If d is the distance between the flange angles of a plate girder, vertical stiffeners are provided at a distance not greater than
d but not less than 0.20 d
1.25 d but not less than 0.33 d
1.5 d but not less than 0.33 d
2.0 d but not less than 0.50 d
A butt weld is specified by
Effective throat thickness
Plate thickness
Size of weld
Penetration thickness
If L is the overall length of a combined footing having A as its area, d being the distance between the centre of gravity of the base and centre of the base, the larger width b is
(A/L) + (3Ad/L²)
(A/L) + (6Ad/L²)
(A/L) - (6Ad/L²)
(A/L) - (3Ad/L²)
As per IS : 800, for compression flange, the outstand of flange plates should not exceed
12 t
16 t
20 t
25 t Where t = thickness of thinnest flange plate
In moment resistant connections, the moment resistance of riveted connection depends upon
Shear in rivets
Compression in rivets
Tension in rivets
Strength of rivets in bearing
The effective length of a double angle strut with angles placed back to back and connected to both the sides of a gusset plate, by not less than two rivets, is
0.5 L
0.67 L
0.85 L
2 L
Slenderness ratio of a compression member is
Moment of inertia/Radius of gyration
Effective length/Area of cross-section
Radius of gyration/Effective length
Radius of gyration/ Area of cross-section
Water pressure in a 80 cm water main is 10 kg/cm2. The minimum thickness of the metal required for the water main, not to be stressed more than 200 kg/cm2, is
1 cm
1.5 cm
2 cm
2.5 cm
Minimum pitch of the rivets shall not be less than
1.5 d
2.0 d
2.5 d
3.0 d Where d is gross diameter of rivet
Minimum thickness of web in a plate girder, when the plate is accessible and also exposed to weather, is
5 mm
6 mm
8 mm
10 mm
Pick up the correct statement from the following:
Dead load includes self-weight of the structure and super-imposed loads permanently attached to the structure
Dead loads change their positions and vary in magnitude
Dead loads are known in the beginning of the design
None of these
Rolled steel beams are:
Mainly used to resist bending stress
Used as independent sections to resist compressive stress
Used as independent sections to resist tensile stress
All the above
The capacity of the smallest pressed steel tank is
1000 litre
1650 litre
1950 litre
2450 litre
Pick up the correct statement from the following:
The steel beams placed in plain cement concrete, are known as reinforced beams
The filler joists are generally continuous over three-supports only
Continuous fillers are connected to main beams by means of cleat angles
Continuous fillers are supported by main steel beams
Rivets connecting flange angles to cover plates in a plate girder are subjected to
Horizontal shear only
Vertical load only
Both (A) and (B)
None of the above
Pick up the correct statement from the following:
Vertical stiffeners may be placed in pairs one on each side of the web
Single vertical stiffeners may be placed alternately on opposite sides of the web
Horizontal stiffeners may be placed alternately on opposite sides of the web
All the above
The internal pressure coefficient on walls for buildings with large permeability is taken as
± 0.2
±0.5
± 0.7
0