What setting gradient allows us to fill an open area?
Gap
Tolerance
Transparency
Open
Correct Answer :
B. Tolerance
Related Questions
If the scheme that stores will be opened in AutoCAD 2006 then you must save it in
AutoCAD 2004 dwg
AutoCAD 2006 dwg
AutoCAD 2007 dwg
None of the above
What do the letters UCS
Uniform Calculator System
United CAD System
Universal CAD Settings
Universal Coordinate System
What does the command Wblock
Warp-speed block
Write block
Window block
Wide-area block
How to make a random line with an angle of 40 degrees to the x axis
will write 0 <40
will write 2 <40
will write 3<40
will write 4 <40
The origin of a drawing is at
0,0
1,0
0,1
1,1
What is the difference between command Plot and Print
plot command prints only big plans
The plot command for CNC (CAM)
No difference
print command can print up to A3 size paper
Is 330 degrees same as -30 degrees in a drawing?
True
False
3.How long will a line from 0,5 to 5,5 be ________
10 units
5 units
15 units
None of the above
When in absolute Cartesian coordinates have points A (10.8) and B (6.5), then to make a line from A -> B with relative polar coordinates will write
@ -5 <36.88
@ 4 <30
@ 5 <216,88
@ 3 <60
What you cannot create from the command Offset
Vertical straight
Concentric circles
Three parallel lines
Parallel arcs
How many layers a drawing should have?
1
2
As many as depending on the complexity
None of the above
If you change the scale list a project that I have started from 1:50 1:10 then
You will have to start over
You should not raise the objects already exist (scale) by 5
You will not need to change anything in hitherto methodology
should be converted into new items that will add based on the new scale
What command allows us to select objects based on some status?
Properties
Qselect
Pselect
Attributes
Where should you pay attention when you are working with autocad commands?
Drawing area
Status bar
Tool bars
Command window
How many points do you need to define for the rectangle command?
One
Two
Three
Four
How many SNAP points does an object have?
1
4
5
Depend on object
Which of the following is NOT a property of an object
Line weight
Measure
Hyperlink
Elevation
Objects are rotated around the
Bottom of the object
Base point
Center of the object
Origin
A surveyor with a headband to measure the dimensions of a site, he make measurements by
No one method
Related Cartesian coordinates
Absolute polar coordinates
None of the above
What is the command used for Plagiostomi angle?
Chamfer
Fillet
Offset
Mirror
Scaling objects make them______
Smaller
Bigger
Either smaller or bigger
None of the above
What is the difference between the Scale command from the command Zoom
Scale for single object, while the Zoom whole plan
No difference
H Scale can grow / shrink a shape up 10 times, while the Zoom has no limits
H Scale changes the size of objects, while the Zoom changes the visibility of the project
Fillet command can be used to obtain_________
Sharp corners
Round corners
Both of the above
None of the above
Print scale 1:50 means that
The draft is 50 times less expensive than the original
A 3 cm corresponds to half a meter
A measure corresponds to 50 cm
None of the above
When drawing in 2D, what axis do you NOT work with?
X
Y
Z
WCS
A polar array creates new objects____
In a grid pattern
In a circular pattern
In a straight line
All of the above
How many AutoCAD objects are in a rectangle?
One
Two
Three
Four
If during the CCW measurement result gives an angle 135 degrees, the same CW angle measured is
225 degrees
-135 degrees
-225 degrees
135 degrees
How would you select set of objects in a drawing?
By a crossing window drawn from right to left
By a crossing window drawn left to right
Shift+ clicking on the objects
None of the above
The primary difference between the Model tab and the Layout tab(s) is ____.
the Model tab is used for drawing in 3D and a Layout is used for drawing in 2D
the Model tab is where you create the drawing and a Layout tab represents the sheet that you will plot or print on
the color of the background
the Model tab displays the drawing you are copying from and the Layout tab is where you lay out the new drawing