1000+ Airport Engineering MCQ for SSC CHSL [Solved]

1. The best direction of a runway is along the direction of
A. Longest line on wind rose diagram
B. Shortest line on the wind rose diagram
C. Line clear of wind rose diagram
D. None of these
Answer : A

2. Which of the following is an example of failure in flexible pavements?
A. Alligator cracking
B. Mud pumping
C. Warping cracks
D. Shrinkage cracks
Answer : A

3. According to I.C.A.O. the slope of transitional surface at right angles to the centre line of runway, is kept
A. 1 in 4
B. 1 in 5
C. 1 in 6
D. 1 in 7
Answer : D

4. According to the International Civil Aviation Organisation (I.C.A.O.) the strength of runway pavements, have been coded by
A. Seven English alphabets
B. Last Seven English alphabets
C. First Seven English alphabets
D. First seven numbers
Answer : D

5. The length of a runway under standard atmospheric conditions is 1800 m. If the actual reduced level of the site is 1200 m, the design length of the runway is
A. 2360 m
B. 2460 m
C. 2560 m
D. 2660 m
Answer : C

6. Pick up the correct statement from the following:
A. Landing speed is directly proportional to the wing loading
B. Wing loading remaining constant, the take off distance is directly proportional to the powder loading
C. Neither (a) nor (b)
D. Both (a) and (b)
Answer : D

7. According to ICAO, all markings on the runways are
A. Yellow
B. White
C. Black
D. Red
Answer : B

8. The maximum length and pavement strength of the runway is that of
A. A 1
B. B 2
C. B 3
D. G 7
Answer : A

9. The capacity of parallel runway pattern depends upon
A. Weather conditions and navigational aids available
B. Lateral spacing between two runways and weather conditions
C. Lateral spacing between two runways and navigational aids available
D. Lateral spacing between two runways, weather conditions and navigational aids available.
Answer : D

10. Assertion A: The width of a taxiway is smaller than the runway width. Reason R: The speed of the aircraft on a taxiway is greater than that on runway. Select your answer based on coding system given below
A. Both A and R is true and R is the correct explanation of A
B. Both A and R is true but R is not the correct explanation of A
C. A is true but R is false
D. A is false but R is true
Answer : C

11. The reduced levels of the ends A and B of a runway are 3025 m and 3035 m and that of its mid-point is 3015 m. The reduced level of the horizontal surface, is
A. 3070 m
B. 3060 m
C. 3075 m
D. 3015 m
Answer : C

12. The reduced level of the proposed site of an air port is 2500 m above M.S.L. If the recommended length by I.C.A.O. for the runway at sea level is 2500 m, the required length of the runway is
A. 2500 m
B. 3725 m
C. 3000 m
D. 3250 m
Answer : B

13. Wing loading of an aircraft is
A. Load of the wings
B. Gross total weight of the aircraft/ load of the wings
C. Gross total weight of the aircraft/ wing area
D. Gross total weight of the aircraft/total available H.P of engines
Answer : C

14. Pick up the incorrect statement from the following:
A. Channelization of pavement is caused by constant use of tri-cycle gears of aircraft
B. Blast pads are used over cohesionless soils to resist erosion due to tremendous speed of the jet blast
C. Over-run areas of at least 300 m length on either side of the runway are provided
D. None of these
Answer : D

15. In approach areas of runways equipped with instrumental landing facilities any object within 4.5 km distance from runway end shall be considered as an obstruction if its height is more than
A. 20 m
B. 30 m
C. 45 m
D. 51 m
Answer : B

16. For Class A Air port the difference of reduced levels of higher and lower edges of the conical surface, is
A. 25 m
B. 50 m
C. 75 m
D. 100 m
Answer : D

17. The length of clear zone for none instrument runway of a small aircraft is
A. 150 m
B. 300 m
C. 600 m
D. 750 m
Answer : B

18. Effective length of a runway is the distance between
A. Ends of the runway
B. Point of intersection of the obstruction clearance line and the extended plane of the runway surface, and the other end of the runway
C. Point of intersection of the glide path and the extended plane of the runway surface and the other end of the runway
D. Ends of the clear way on either side
Answer : B

19. As per UK design criteria, if LCN of aircraft is between 1.25 to 1.5 times the LCN of pavement, then the number of movements allowed are
A. Zero
B. 300
C. 3000
D. Unrestricted
Answer : B

20. Conical surface of the approach area rises outwards
A. 1 in 10
B. 1 in 15
C. 1 in 20
D. 1 in 25
Answer : C

21. The threshold markings are
A. 4 m wide
B. 1 m clear space between adjacent
C. Placed symmetrically on either side of the runway centre line
D. All the above
Answer : D

22. Which of the following factors are taken into account for estimating the runway length required for aircraft landing?
1. Normal maximum temperature
2. Airport elevation
3. Maximum landing weight
4. Effective runway gradient Select the correct answer using the codes given below Codes:
A. 1, 2, 3 and 4
B. 1, 3 and 4
C. 2 and 3
D. 1, 2 and 4
Answer : D

23. Pick up the component not applicable to aeroplanes
A. Wings
B. Engines
C. Air screw
D. None of these
Answer : D

24. The strength of winds is measured with the help of
A. Beaufort scale
B. Wind indicator
C. Barometers
D. None of these
Answer : A

25. Beaufort scale is used to determine
A. Strength of winds
B. Direction of winds
C. Height of air-crafts
D. None of these
Answer : A

26. Calm period is the percentage of time during which wind intensity is less than
A. 4.8 kmph
B. 6.4 kmph
C. 8.0 kmph
D. 9.6 kmph
Answer : B

27. Pick up the correct statement from the following:
A. Minimum turning radius of aircrafts decides the size of the apron and the radius of the curves at taxi-ends
B. Take off and landing distances for an aircraft, determine the minimum runway length
C. The length of the normal haul of the air craft decides the frequency of operation
D. All the above
Answer : D

28. Which of the following is used for servicing and repairs of the aircraft?
A. Apron
B. Hanger
C. Terminal building
D. Holding apron
Answer : B

29. The air is blowing at a speed of 75 knots in the direction of the aircraft flying at a ground speed of 775 knots. The air speed of the aircraft, is
A. 775 knots
B. 75 knots
C. 850 knots
D. 675 knots
Answer : D

30. In an airport, if 4 groups of 5 gates each located well separated are considered for traffic and the future to present traffic ratio is 3, then the total requirement of future gates will be
A. 32
B. 36
C. 44
D. 68
Answer : B

31. The centre to centre spacing of heliport lighting along the periphery of landing and takeoff area should be
A. 2.5 m
B. 5.0 m
C. 7.5 m
D. 10.0 m
Answer : C

32. Pick up the correct statement from the following:
A. The distance between the points of intersection of the extreme tangents to the transition curve is kept greater than 7500 m × sum of grade changes at the point of intersection
B. The rate of change of grade is limited to 0.3% per 30 m length of the curve
C. According to I.C.A.O. the maximum longitudinal gradient along a runway is limited to 1.5%
D. All the above
Answer : D

33. Pick up the correct statement from the following:
A. The speed of the aircraft relative to the ground, is called cruising speed
B. The speed of the aircraft relative to wind, is called air speed
C. When wind is blowing the direction of the flight, air speed is less than cruising speed
D. All the above
Answer : D

34. The bearing of the longest line of a wind rose is S 45° E, the bearing of the runway will be numbered
A. 135°
B. 31
C. 13
D. Both (c) and (d)
Answer : D

35. The lift off distance is the distance along the centre of the runway between the starting point and
A. End of the runway
B. End of stop-way
C. Point where air craft becomes air borne
D. Point where air craft attains a height of 10.7 m
Answer : A

36. For supersonic transport aircraft, the minimum turning radius of taxiway is
A. 60 m
B. 120 m
C. 180 m
D. 240 m
Answer : C

37. The cruising speed of the aircraft is 500 kmph. If there is a head wind of 50 kmph, then the air speed and ground speed of the aircraft respectively will be
A. 450 kmph and 500 kmph
B. 500 kmph and 450 kmph
C. 450 kmph and 450 kmph
D. 500 kmph and 500 kmph
Answer : A

38. For determining the basic runway length, the landing case requires that aircraft should come to a stop within p % of the landing distance. The value of p is
A. 40 %
B. 50 %
C. 60 %
D. 75 %
Answer : C

39. The length of runway under standard conditions is 2000 m. The elevation of airport site is 300 m. Its reference temperature is 33.05°C. If the runway is to be constructed with an effective gradient of 0.25 percent, the corrected runway length will be
A. 2500 m
B. 2600 m
C. 2700 m
D. 2800 m
Answer : C

40. As per ICAO, for airports serving big aircrafts, the crosswind component should not exceed
A. 15 kmph
B. 25 kmph
C. 35 kmph
D. 45 kmph
Answer : C

41. If lift off distance of an craft is 2000 m, the clear way at the end of the runway should not be less than
A. 145 m
B. 152.5 m
C. 162.5 m
D. 172.5 m
Answer : D

42. The bearing of the runway at threshold is 290°, the runway number is
A. N 70° W
B. 290°
C. 29°
D. W 20° N
Answer : C

43. As per ICAO, for A, B, and C type of airports, maximum effective, transverse and longitudinal grades in percentage respectively are
A. 1.0, 1.5 and 1.5
B. 1.0, 1.5 and 2.0
C. 1.5, 1.5 and 2.0
D. 2.0, 2.0 and 2.0
Answer : A

44. The main disadvantage of angle nose out parking configuration of aircraft is that the
A. Aircraft rear loading door is far away from terminal building.
B. Hot blast is directed towards the terminal building
C. Overall apron area required is more
D. All the above
Answer : B

45. The runway orientation is made so that landing and takeoff are
A. Against the wind direction
B. Along the wind direction
C. Perpendicular to wind direction
D. None of these
Answer : A

46. Pick up the correct statement from the following:
A. Approximate geometric centre of the landing area, is called air port reference point
B. The boundaries of horizontal surface and conical surface are marked with reference to air port reference point
C. The location of the air port on a map is the position of air port reference point
D. All the above
Answer : D

47. As per ICAO recommendation, the rate of change of longitudinal gradient per 30 m length of vertical curve for A and B type of airports is limited to a maximum of
A. 0.1 %
B. 0.2 %
C. 0.3 %
D. 0.4 %
Answer : A

48. Runway threshold is indicated by a series of parallel lines starting from a distance of
A. 3 m from runway end
B. 6 m from runway end
C. 10 m from runway end
D. 15 m from runway end
Answer : B

49. Pick up the correct statement from the following:
A. The centre line of the approach area coincides with that of the runway
B. Approach areas are measured in horizontal surfaces
C. Obstruction clearance surface and approach surface are same
D. All the above
Answer : D

50. The distance between main gears is 10 m, and the distance of nose gear from centre of main gears is 30 m. If the angle of turning is 60°, the distance of centre of rotation from the nearer main gear, is
A. 12.30 m
B. 11.30 m
C. 10.30 m
D. 9.30 m
Answer : A